before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hello, I am using the nRF54L15 DK board, and trying to connect to the FLPR RISC-V coprocessor in the SoC.
I have been able to do so, and can have both processors running...
I have installed NCS V3.0.0, nrf54L05
I'm currently working on the ESB and BLE coexistence feature, but I've run into some issues.
In ,config file
I find that TIMER10...
Hello,
We have the following environment:
1) nRF Connect SDK v3.0.1
2) The custom board with nRF54H20
3) Our project with update capability using SUIT file.
...
I'm trying too use a timer as a counter on my nRF52840. This is the function in question:
static void timer_init ( void )
{
nrfx_timer_config_t timer_cfg = { ...
Hi NordicSemi
We might have mixed up different SoC versions of the nRF54L15.
According to the following page, there are different SDKs that supports different HW versions...
I want to evaluate Bluetooth LE Channel Sounding on the nRF54L15, using multiple antennas. The nRF54L15DK only has one antenna, so if I use it as both initiator and reflector...
I am experiencing issues programming my newly purchased nRF52840 DK, which has never been successfully flashed. After following the official starting guide on nordicsemi.com...
When Enabling an advertising set already enabled on the Softdevice Controller, the HCI error command disallowed is produced when according to the BLE specification 6.0 it...
Hi everyone, I am attempting to configure two of NRF5340DK modules to execute ISO_Connected_Benchmark. I have tried to configure ipc_radio to compile for cpunet and application...
Hi everyone,
We're using the "Manufacturer Specific Data" field within its advertising packets to send the firmware version to a phone application. It requires the company_indentifier...
1st issue: Tingy91X doesnt build at all with debug -Og enabled: Because of all the strange issues of Thingy91 (nRF9151) and "not to be used in new products) we ordered a couple...
Hello,
I would have a question regarding the use of PCAL6408A I/O expander on nRF9151 DK. The buttons and LEDs on nRF9151 DK are connected both directly to the processor...
We are planning to run a small proto build, and looking to program a small quantity of nRF54L10, prior to the SMT. These are loose parts (not built onto any PCBA). I am hoping...
I recently switched from evaluating an nRF52805 (Fanstel BC805M) to an nRF54L15 (using the nRF54L15-DK), and after I updated the toolchain and tried to flash the kit (using...
checking in if anyone is successfully using an open debug-probe for nRF54L series?
...guessing nordic is using segger OB on the DK's because of the Risc-V not fitting...
