Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Hi,
I want to use external power (battery) and USB power together.
If USB is not connected, I want to supply it with battery power, and if USB is connected, I want to...
Dear HW engineer,
I have ordered a few custom boards with nRF52820. As recommended by the datasheet, I have used 12pF load capacitors for both HF (32MHz) and LF (32kHz)...
Hello
I use nrf52832 and SDK v17.
I'm conducting various tests on Bluetooth. And I faced a lot of new problems. I erased a previously saved bond from the Android nrf connect...
Hi
After successfully testing nRF9160 SLM app. we plan to use nRF9160 with UDP and LwM2M protocol in our smart devices. We also have our private cloud server where all the...
Im new using Nordic devices , I am trying to using nrf52840DK to locate nrf52840 dongles using the direction finding method , how can I connect the dongles to the DK and build...
HI,
Is it possible to update modem firmware from 1.2.0 straight to 1.2.2? Or is it the only way to first update from 1.2.0 to 1.2.1 and then to 1.2.2?
Regards, Tero
Hello
I'm testing the firmware using the BLE. When I upload, I can see that the board is working. Also, I don't think there's a problem with running each line of debugger...
I'm trying to build the blinky zephyr sample for nRF Connect SDK and get the following failure:
Creating solution blinky.emProject
/usr/local/bin/cmake -GNinja -DBOARD...
How can I, from the pc-ble-driver API, send an insufficient authentication request without configuring a characteristic to be secured?
I am testing out new standards. One...
Hello, Nordic community,
I want to implement OTA using Thread with nRF Connect SDK.
Is there any sample code or reference this can be done with Thread?
Thanks,
...
Is there a limit to the number of handlers that can be registered using NRF_PWR_MGMT_HANDLER_REGISTER? I can't seem to get any more than 3 to be called, changing NRF_PWR_MGMT_CONFIG_HANDLER_PRIORITY_COUNT...
Hi--I'm part of a research group that will be using the Thingy 52 to record environmental variables, and we will need to transfer information to a cloud server using a satellite...
HI，ALL：
How to setup TX mode in example PRX，and so,how to setup Rx mode in PTX example. I use esb_init() of example PTX in example PRX， But when I fill data in fifo, it...
HI，ALL：
when using ESB example ,the transsmit waveform is below(in channel 3):
how to make it more simple,like that as below(other example in channel 3):
