I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Hi everyone,
I want instead of MAC address to advertise my device using its 64bit unique ID. What I am considering, is to use the p_data array for that purpose and more...
Hi, I see an interesting situation.
I got flash corruption with values 0xff after random power cycling and it's happened only if I have flashed the bootloader
soft device:s132
sdk:15.3.0
I implemented the following, but the event does not occur even if the voltage is V2.8 or less.
Do you know the reason?
===
NRF_SDH_SOC_OBSERVER...
The nRF5 SDK's throughput sample (ble_app_throughput) provided very convenient shell commands to configure key parameters affecting throughput in a connection, such as ATT...
Hello,
in my project I have a custom board with a nRF52832 chip, which reads 4 channels with a sample rate of 1kHz (1ms). The SAADC readings get transmitted to a nRF52840DK...
soft device:s132 sdk:15.3.0 board:nRF52832 board (taiyo yuden EYSHCNZWZ)
Unable to receive event 'NRF_EVT_POWER_FAILURE_WARNING' I implemented the following, but the event...
Hello
Using the timer, I am making code that turns on LED1 to 3 sequentially. I thought it was going to be very simple, but it's not going as well as I thought.
I'm making...
Hi, I have very STRANG issues. I am adding custom Characteristics to custom Services. I have added 10 custom Characteristics with the same config 8 of them are working perfectly...
Hi,
I am on ncs master branch, when i build and load the Serial LTE Modem(SLM) application the application struck at mcuboot
The only additional configuration option i...
I am using nrf52840 board. I hvae interfaced a gsm module(quectel m66).The problem is my device gets an APP_UART_FIFO_ERROR after every few sms commands.The maximum data i...
Hello everyone!
I have an issue about upgrading firmware over Bluetooth LE with a mandatory pairing of devices. I want only paired devices to have the ability to upgrade...
hello,
In the nrf51822 sdk 5.1 I can see a routine named ble_app_ibeacon.
I find a parameter define as below,the data is added to the advertising data.
#define APP_MEASURED_RSSI...
Hello,
Our team has narrowed down a particularly interesting issue with the boot sequence / initialization of our BMD-341 chip, which itself runs the nRF52840 SoC. For context...
Hi , i am using the nRF52DK and i have a small problem with the pwm driver.
i basically would like that the frequency increases if i press a button or decreases if I press...
