Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hello, guys
I have nRF9151-dk running Serial LTE Modem (SLM) app on it and want to test the ability of working with sockets (open socket, send/receive data, close the socket...
Hi all,
We have designed a custom board including a NRF52805 chip. We also followed PCB design guidelines and used the exact PCB layout recommended by Nordic. As expected...
Hi folks, thanks in advance for your support.
The thing is that in my SEGGER project I didn't have explicitly linked a bootloader to be flashed in the device (nRF52832)...
nRF52832 & NCS v2.6.1
I merged the NUS central and NUS peripheral FW into a single one where the user calls appropriate initialization functions to activate whether central...
Hi,
I am trying to write a simple application that uses I2C on a nrf5340 DK, assigning SCL to P0.9 and SDA to P0.10, using the app core ns . The application builds without...
Hello,
I am working with the nRF9160DK and the Thingy 91 to do some basic evaluation.
I was wondering if these devices supported Private LTE connections.
Thanks.
On Seeed Xiao nRF52840, I'm attempting to use reset (P0.18) as GPIO in a Zephyr (ZMK) app.
I've set
```
&uicr {
/delete-property/ gpio-as-nreset;
nfct-pins-as...
We want to be able to toggle between 128 MHz and 64 MHz on our nRF5340 based custom board depending on whether our audio pipeline is in process or not. However, a note in...
I am facing a similar issue described in https://devzone.nordicsemi.com/f/nordic-q-a/97084/direct-xip-mcuboot-both-images-have-the-same-version where mcuboot is unable to...
Hi everyone, I'm here to ask if anyone could help me solve the problem I'm having when programming on the nice!nano board. In my project, I created a new board called nice...
I recently purchased an nrf52840 dongle.
In nRF Connect for Desktop (v5.0.2) and with or without the device attached, Programmer (v4.4.1) starts with a rust-panic error...
Hi all,
I'm really new with nrf zephyr environement, so for now I've build a custom board build with nrf9161 (look similar to circuit dojo feather nrf9160). I'm able to...
We would like to change BLE's PHY setting 2Mbps to 1Mbps in Audio profile. In SDK ver2.3.0, we could find BLE's PHY setting as follows;
Let me confirm the point to be modified...
Hi there:
I want to do BLE FOTA on nRF5340 Audio DK board. I have sdk v2.6.2. I'm trying to make the existing audio application work by taking the source code as it is from...
So I am using the NRF5340, and it has been fine for a few months now, however today, it stopped working and sending any data between the USB and laptop, the LED5 flashes once...
