Hi ,
I would like to know if a matching network is needed if I am only using a single external flex antenna for both LTE and GPS using a RF switch between them and a uFL...
I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hello,
I' have problem with CMAKE and Zephyr in VSC. Please, see following error:
[main] Building folder: blinky_13
[main] Configuring project: blinky_13
[proc...
hi,all
I Need add many characteristic with notify in one service,and I wish it can send notify to the phone once the phone enable cccd.
1.tx_handles can work,buf rx_handles...
Good day,
I am developing app by SDK 17.1.0, including ble_nus and ble_hid, I would like to imply fuction to switch between ble_nus and ble_hid, due to some difference configuration...
Hi!
I am trying to subscribe to the power management events that correspond to the following log lines (which I can clearly see in the log):
I have been trying with this...
Hello All,
I'm currently now on the initial phase of development and i wanna to stream 2xIMU data through SPI as for now if i connect only one IMU as Follow
P1.15 SCL...
Dear all and Nordic Staff:
I am learning about dynamic multiprotocols and found examples of dynamic multiprotocols for Thread and BLE in the "nRF5 SDK for Thread and Zigbee...
Due to the system design of our products, I am going to need to sideload any firmware update binaries. That is, my application code will handle receiving the update through...
Hi
I am using ncs v2.3.0, mesh chat example
I have used CONFIG_BT_CTLR_TX_PWR_PLUS_8 =y , and it works quiet well, now how can i implement CODED_PHY (long range) in this...
Hello,
I came across a Nordic Q&A discussing a sample called hci_uart_with_usb_uart_bridge in this post . I have searched in the v1.0.1 tag but couldn't find the mentioned...
Hello,
I'm attempting to establish communication between an nRF52840 and an nRF9160 on the nRF9160DK using LPUART. Initially, I tried using the interrupt-driven mode, but...
I get the registration "parse_cereg: LTE mode not found, error code: -22" error,when try to connect to LTE network in china shenzhen.the hardware is custom use nrf9160 chip...
sdk 2.1.0
nRF9160
Hi, I need to parse a JSON file and for that I'm trying to use zephyr's json.h library. Based on the automatic test file I built a piece of code for...
Hi,
I am trying to use an ST7789 display with the NRF9161DK, I was following this guide but got no luck:
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b...
Hi,
I was looking into hooking up an SD card to the nRF9160DK that I use for data collection during evaluation and early stage pilot projects. I noticed that there is an...