I am a student interested in Nordic.
My coding skills are very poor.
So I want to get help.
I want to use the vl53l1x sensor in nrf52. (My ultimate goal is to measure...
I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hello,
We’re testing the nRF9160 GNSS performance on our custom PCB and have noticed that, even with A-GPS, the first fix after powering on the device takes significantly...
I am having problems flashing my custom board with a nrf5340 chip. Sometimes it works, sometimes it does not, but more often than not it doesn't work and I cannot figure out...
Hello Nordic Team,
I’m trying to use the nRF54L DK to program an external MCU via SWD , but I’m encountering an error during connection. I’ve already followed this guide...
I'm trying to build the light-switch-app from Matter but I get following errors
I have already tried to reinstall the sdk (I use v2.8.0) and build it just like that without...
After modifying the factory data with the script generate_nrfconnect_chip_factory_data.py, the discriminator and passcode work, but how do I change the value of the Manual...
I am trying to interface an SD card with the nRF9160-DK using an SD card adapter module. My goal is to write the string "hello" to a .txt file on the SD card. I believe I...
Is a TVS diode clamping voltage of 6.5 V acceptable for supplementing the built-in ESD protection of the NRF52840 GPIO pins?
It has been previously established in the forum...
Hello everyone!
I am rather new to firmware development with Nordic products and am experiencing some trouble with the Thingy91 LTE BLE Gateway sample.
What is the problem...
Hello,
I want to set my TTL value in a node (nrf52840 dongle) that i use as a relay node.
In prj.conf file I set the node in this way:
CONFIG_BT_MESH_RELAY=y
CONFIG_BT_MESH_RELAY_RETRANSMIT_COUNT...
Hi
I've recently tried to move from SDK version 2.6.3 to 2.9.1. However i've run into issues with this transistion.
I made a new custom board, by following the guide...
Hi , i am trying to use ble channel sounding feature through hci uart with an external host. I am sending CS commands but getting the following error for one of the commands...
Hi,Team,
I am developing Pawr using nrf54l15-dk.
I want to realize the connection and communication between the broadcaster and the upper computer software nRF Connect...
Hi there,
One of the functions of the DECT MAC layer is to allocate radio resources to RDs. According to the standard, the MAC layer does that using special beacon messages...
Hi Nordic team.
I'm finding a way to update the factory data over-the-air. Specifically, I want to update the Matter Certification information (PAI, DAC, ...) over-the-air...
I have a few questions about the new privacy requirements added to the RED for CE certification starting in August 2025:
Does ANT+ still comply with these new requirements...
