Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I'm adding DFU over Bluetooth support to an existing application based on nRF Connect v2.3.0 following these instructions . What the instructions lack (and possibly is a given...
As the title suggests, I am trying to run the peripheral LBS example on my custom PCB to test BLE before continuing with my application. I'm using NCS V2.9.0. I have created...
In some other tickets it's said, that using the nRF7002 for IP traffic doesn't work, because that requires too many resources on the nRF9151.
Does this apply for a "UDP...
Hi,
Where are the peripherals required for the Zigbee stack documented? I have searched, but only broken links have been returned by Google. I'm using Connect SDK v2.9
Hello. I want to change the board configuration in nrf7002. "In the nrf7002dk_nrf5340_cpuapp.dts file &spi4 { status = "disabled"; }; An error occurs when spi4 is disabled...
Hello everyone,
My project consists on using the nPM1300 with ESP32-S3 on a custom board. I2C connection is pretty much validated, since I have already configured some...
I have an app where I'm using the AP and STA mode of the 7002. I'm running on a nrf5340.
*** Booting nRF Connect SDK v3.5.99-ncs1-1-1-g6dc48c918694 *** [00:00:12.620,269...
Hello,
I am new to Zephyr and I am trying to figure out the best way to set up a new project for a nRF91 modem. Ideally, the project should allow patching of the nRF Connect...
Dear All,
I am working on a project using the nRF52810 with the secure bootloader configuration from the Nordic SDK 17.0.2 . Specifically, we are using the example:
....
I've setup my development environment using the 'application' structure. https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/develop/application/index.html#zephyr_workspace_application...
With the nRF52840 we used RSSISTART to start the sampling of the RSSI and got a RSSIEND event when we could read the RSSISAMPLE register.
The radio on the nRF54L doesn't...
Hello,
I am working with the Multi-Service sample on the 9161dk and also a custom 9151 board.
The multi-service sample compiled option works great but the samples, when...
Greetings.
Background:
We have a custom device, that uses the nRF9160 as a Modem, with Modem OS 1.3.4 and a sightly modified "Serial LTE Modem" FW. One of our Devices...
I'm trying to send simple packets using the radio peripheral.
In my test scenario I have the following conditions:
The HFXO is started and is running the whole time...
hi
the lengths of the this track is important?
if i decrease this length, how i can set antenna parameters?
another question: what is the R1 =0 ohm resistor and N...
