Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Whether BLE 5.0 support for audio stream? Also, I want know it is possible to connect 2 headsets+2 TPMS device+1 Phone with a single device at same time? And it shall able...
Hi,
we ordered by Data I/O the Algorithm for the device NRF52833-CJAA-R
For this we need a documentation (datasheet) including the CSP-Package (CJ) with pin-description...
Hi All, New user here but couldn't find a concrete answer to the following question. In PIC land I've usually allocated fixed memory using the _at_ or __attribute__ label...
Hi. I have a problem with my NRF52840 Dongle. When using BSP driven button. I've tried to use some SDK precompiled examples - it doesn't work. Neither with ble_peripheral...
Hello,
I am trying to add application specific errors codes to the error handling framework in the nRF51K SDK. The documentation in sdk_errors.h says that a range is reserved...
Is there an error code range reserved for user application errors?
I wish to return application specific errors without defining a new error type, to maintain a unified...
Hi,
I'm using nRF Android Mesh library from here for to build a cordova plugin for my project. So i almost completed my plugin but when i'm testing the plugin using nRF52...
Hello
i need to make BLE Dongle (reproduce without having documents, just a page how to update Firmware)
i need to be able to programm a .hex file i have via nRFgo Studio...
Recommended nRF52820 dev kit is nRF52833 DK because dev kit for the 20 are not yet available.
Is the nRF52840 DK also compatible or the nRF52833 DK have something special...
With the Eddystone beacon example from the nRF5 SDK v.16.0 I managed to change the beacon data to be sent using es_slot_on_write. This only changes though if this data is...
Hi,
we spent 2 days of debugging why our application doesn't work on new nRF52820 & nRF52833 in QFN40 package. And today, we found out that some of the pins have probably...
Hi,
I`m considerate to use Nordic SoC in my design.
Please advise if Nordic have BLE SoC with Capacitance Touch Sensing capabilities like in Cypress part CY8C4127LQI-BL483...
So, I am adapting and adding to a project based on the example app with SDK16.0 and softdevice s112. I'm using Keil.
My nrf52832 has 256kb flash, 32k ram.
I'm compiling...
Are there any examples of how to configure the COEX pins between the 9160 and a 52840 such that each will actually use the signals to start/stop their respective radios? The...
I see references to a get (0x8046), set (0x8047), and status (0x8048) messages for Node Identity. Where could I find documentation about these messages? There is no sample...
