what can be the starting Point for Bachelor Thesis involving BLE 5.0 devices to be deploy in mesh Network. How the challanges in the Thesis can be address and set as a Goal...
Note: This is related to the following issues:
- https://devzone.nordicsemi.com/f/nordic-q-a/63255/nrf9160-getting-stuck-after-cell-change
- https://devzone.nordicsemi...
Hi, I am Product Manager working for Medical Device Manufacturing company based out of Ireland.
we are in search for a development house / developer who will support us...
I have so many versions of this topic that I now am certain that most of the answers provided are wrong. Since you cannot have so many ways of connecting an external nrf device...
Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I am a little bit confused about the different supported stack for the nRF52833 when using BLE Mesh. With the current example, there is only support for the S113. Can...
I started a timer on the nrf52840 and the SDK is nRF5_SDK_15.2.0_9412b96, but I haven't never receive the callback message after the time. What's the reason?The code is as...
Hello ,
In this scenario, I have to measure the time interval between the START and STOP pulses generated by a peripheral device connected to nRF52 DK. The thing is START...
Hello!
I am currently using a module called BLENano2 (nRF52832). SDK15.0.0 is used and the editor is "Segger Embedded Studio v4.16".
Finished writing the program that...
Hi,
I tried out the light switch example on a nRF52833 and it seems not to be reliable at all. So i connected the debugger and saw, that in access.c,
in packet_alloc_and_tx...
Hi all,
I am trying to use nrf52840 dongle as hci_usb with the very simple task: scan
Host is Raspberry Pi with BlueZ
Controller is nrf52840 dongle with firmware hci_usb...
Hi
I want to move DFU at the application level. Is this possible? I want to move DFU at the application level because of my project requirement.
1. In my project, I have...
Hi, I am trying to get the BLE values on Thingy91 (PCA20035) . And I have followed the
devzone.nordicsemi.com/.../217018 I have ported the diff (nrf and zephyr diffs from...
I am using built-in DTLS for encrypting my UDP traffic. In order to save expensive data quota and reduce battery drain, I have to make use of session resumption, so that I...
Hi. I have a question about Bluetooth 5.1. I just want to know what the main difference is between a Bluetooth 5.0 and Bluetooth 5.1 chip.
Is it the hardware or software...
I am developing a firmware on a nrf52840 board with FreeRTOS. Unfortunately, due to a mistake during the development process, the board misses the XTAL 32,768 Hz.
Is there...
Hi Nordic:
I want to build a raspberry connected to a 52832 board via uart,
this raspberry pi with 52832 board need doing secure DFU to remote BLE device, the raspberryPI...
Using the nRF9160 on the Verizon network we are having some issues with eDRX. Specifically sending data to the device from our MQTT server.
We have configured a eDRX interval...
Hi,
I am working on nrf52 msc example. I am required to use internal flash for msc. In example there is support for ram, sd card and spi flash. I am required to use internal...
