HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hi all — I'm developing a custom nRF5340 development board (Raytac MDBT53-1M) and would value the community's honest read on whether it's worth producing.
The goal is...
Dear Nordic
At ncs3.2.0 zephyr sample, we found uvc sample as below.
https://docs.nordicsemi.com/bundle/ncs-3.2.0/page/zephyr/samples/subsys/usb/uvc/README.html#uvc
...
I am currently trying to get hello nRF Cloud example running. However, my Thingy:91X doesn't connect with the nRF Cloud. According to the logs of the cellular monitor application...
If the BLE_GAP_ADV_FLAG_LE_GENERAL_DISC_MODE is not set successfully in the broadcast settings, it will result in an error of NRF_ERROR_INVALID_FLAGS when calling sd_ble_gap_adv_data_set...
I see from the SAADC page of the datasheet that there is an internal 0.9V reference on the nRF54L15, but I don't how this reference is generated. Is it an active regulated...
Environment
My hardware is the nRF9151DK dev kit and a custom board with nRF9151 (Monkeytronics Airsmart Cellular Beta 3).
Using nRF tools and SDK v3.1.1.
Using Onomondo...
I used nrf54L15 chip P2 port's SPI.used spi_transceive_dt tx 10 bytes. but chip divide two process (8Bytes+2Bytes).this result is not my object. code as below:
int spi00_dma_transceive...
Hi, The RebootCount attribute of the GeneralDiagnosticsCluster is returning a FAILURE response.
This issue is causing failures in Matter test cases TC-ACE-2.1. CONFIG_CHIP_LAST_FABRIC_REMOVED_ERASE_ONLY...
Hello,
I'm trying to put the nRF54L15DK into System Off mode, using sdk & toolchain version v2.8.0.
The provided example (\samples\nfc\system_off) works on my evaluation...
Hello, modem_shell sample build throws error “undefined boot_write_img_confirmed” with nRF Connect SDK 3.2.1. This issue didn't exist in nRF Connect SDK 3.1.0. I did a quick...
Hi I have updated th nRF Connect for VS Code Extension Pack to the newest version. But when I want to enter Debug in VSCODE, the error comes out. Before upgrade, the debug...
Hello,
I am currently working with an nRF5340 configured to operate in High Voltage mode , where the main input supply is 5 V .
Issue description
When the nRF5340 is...
I just wanted to notify that I need to set CONFIG_SOC_NRF_FORCE_CONSTLAT=y in order for a NRF54L15 to be able to respond as a SPI slave (SPIS) using nrfx SPIS code.
Otherwise...
Hi,
I have developed custom hardware based on the nRF9151 chipset.
I would like to program the firmware using nRF Desktop (Programmer) with a third-party SEGGER J-Link...
