i'm writing bare-metal code for the FLPR (which was loaded by a bare-metal launcher running on the M33)....
when my FLPR code "idles" using the WFI instruction, power consumptions...
I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
Hi there,
We are intending on using the serial LTE Modem example on our nrf9160 with MQTT. What version of MQTT is supported on this example?
Kind regards,
Frikkie
Hi,
I have been using I2C code for almost a year to talk to a variety of sensors with complete success. Typically, we have used a Nordic BL654 module that includes an nRF52840...
I'm getting a strange amount of error when trying to measure the battery for a custom PCB based on the nrf9160.
Details
My VCC_IO is 1.8V
My max battery voltage is...
Hi,
Perhaps I have a misunderstanding of this GNSS Socket Option.
In the GPS Sample Project (samples/nrf9160/gps) with a nrf9160-dk and no connected GPS Antenna, I set...
Hello, I am trying to add a watchdog timer to my code which consists of THREE threads, so I referred to the task_wdt example in Zephyr/Samples/Subsys for SDK1.6.1.
Based...
Hi,
I wonder if there is a smart and easy way to implement a fallback if I use the MQTT connection with a static IP. What I want is if the IP fails to connect it tries again...
this error shows after the 100% completion of memory flash as shown in the screenshot below. after showing the error , nrf52840 pulsing led turns off automatically.
Note...
Greetings All,
I am trying to connect an nrf52840dk board to an nrf52840dongle for wireless serial communication.
I flashed the nrf52840dk with the central_uart sample...
Hello,
I am using nrf52832 and i am using a SW similar to the beacon.
I tried 2 configuration:
tx_power = 0 (0 dbm)
tx_power = 4 (4 dbm)
I tried to measure the...
Hello,
I'm familiar with the GPIO and GPIOTE peripherals,
The GPIOTE has 8 channels, so it can use 8 GPIO pins to fire interrupts.
Some questions:
- Can the 8 Channels...
I've successfully built the 'direction_finding_connectionless_tx' project and flashed that to an nRF52833dk, and built the 'direction_finding_connectionless_rx' project with...
Hi,
I'm using a NRF52811 on a custom board and I would like to change a project from a NRF52832 with S132 to it.
I only use supported functions from the S113, but I...
how to set the High-drive QSPI?
NRF_GPIO_PIN_H0H1
nrf_gpio_cfg ( mosi_pin ,
NRF_GPIO_PIN_DIR_OUTPUT ,
NRF_GPIO_PIN_INPUT_CONNECT ,
NRF_GPIO_PIN_NOPULL ,
NRF_GPIO_PIN_H0H1...
Environment:
- OS: Ubuntu 20.04 (Docker container)
- NRF SDK: v1.4.0
- Zephyr: v2.4.0-ncs1
I am trying to build my project for native_posix. I am getting some build...
