I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
Hello!
We are on the process of implementing our own desktop program to run DFU over BLE, similar to how the nRF Connect application does it. We are using SDK 17.1.0 in...
Hi,
I am using NCS v2.4.2 and nRF5340DK + nRF21540EK but I can not enable GPIO+SPI mode.
for example, I use nrf/samples/bluetooth/central_and_peripheral_hr application...
I am working through BTLE Fundamentals, Lesson 6, Exercise 2, and running the code from blefund_less3_exer2 per the instructions and it all looks good on the app COM log:...
Hi ,
I would like to know if we can use 2 PPK's in such way to measure both direction.
As you can see in the diagram , the current can flow to the battery or can flow...
The bluetooth program refers to app_ble_uart. Bluetooth uses nRF52840. I use stm32 MCU to transmit data through UART. The baud rate is 460800 for transmission. The UART transmission...
I am using nrfConnect for Visual Studio Code 2.6.1 and I am being asked what version of Zephyr I am using when diagnosing a problem in a Zephyr forum. There has to be some...
Hi
Seems like all new nRF DKs shipped with nRF5340 as interface mcu have limited speed on Debug Out.
nrfjprog -r --clockspeed 646 Applying system reset. Run. nrfjprog...
I need to send a JWT to a non-nordic server. They ask for a small struct to be encoded and sent as a string in a larger MQTT message. For example:
That struct is encoded...
I have flashed the light_ctrl hex file in nrf52840 dongle. Flashing Have been completed sueccessfully for provisioning in nrf mesh application its not showing in the network...
Hello,
For a Uni Project I want to measure the current of the Nordic Thingy:91 and visualize it. Therefore i bought the Power Profiler Kit 2. But i dont know how to connect...
So when changing the hci_icp.conf settings to have the configuration below, i get "CMake Error at C:/ncs/v2.6.1/zephyr/cmake/modules/kconfig.cmake:358 (message):" plus the...
My device is peripheral. I added a few lines before the advertisement start in main(). The whole project is in main and simply advertise and get connected and bonded.
...
I want to configure the ESB and nRF21540 chips on the NRF21540-DK. In order to compare the signal gain, I used the nRF52832-DK and burned the Bluetooth routine (without any...
Hello,
I have a project working on Nora B1, which I am testing on nrf5340DK. It is based on the Peripheral UART Sample, programmed with nfr Connect SDK v1.9.1. Now I need...
Hello,
This is probably a dumb question but, I'm having issues with an initial prototype for a product that has been given. The hardware engineer (me) designed and got...