Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I'm embarking on a new project involving a sensor network of up to 3000 devices within a warehouse for industrial monitoring, and I'm considering an OpenThread network-based...
Hello,
I'm working on an application where we're implementing the nPM1300 and utilizing the fuel gauge algorithm to estimate battery life. Interestingly, the results that...
Hello,
I am attempting to connect a ST7789 to the nRF9161 and communicate with SPI. However the display is not working and I suspect it is because the gpios output the VDD...
Dear All,
When i connect the nRF5340 Audio DK to the windows PC through the USB, It will be enumerated as a USB audio device.
And then, It will act as the default audio...
Hi, I'm currently using nrf52840 MCU for product development and almost finished my project. What I want is when producing a product, I want to compare the checksum of the...
I am trying ADC readings for connecting my sensors. To better understand and see the values, I have made a simple connection with 4 10k Resistros in series, VCC on top and...
I am working on an nRF52832-based project and I am encountering an issue with achieving low sleep current. Despite setting the TX power to 0 dBm and the advertising interval...
I am thinking of using the sample source code of nRF5340 Audio to realize LE-Audio on a board created by our company.
I have written the source code of nRF5340 Audio to...
Hi, I am pretty new to programming with NRF boards and I've hit a bit of a roadblock.
I started with the BLE Event Trigger example and I have managed to retrieve BLE advertising...
HI Noridc
I am developing with nRF5340, and I need to proceed with DTM test to verify the chip in the production process.
I am currently using this routine C:\ncs\v2.6...
Hi, I'm working on a ble peripheral that uses nRF5340, NCS recently upgraded to v2.6.1, Zephyr v3.4.99. The net core is running the HCI RPMsg controller sample as it is. In...
Greetings all. I am troubleshooting an issue on my BLE sniffer setup. While I don't 'think' this is causing my actual current failure (Wireshark not detecting COM6) I wanted...
hardware:nrf5340dk
case: Bluetooth: Direction finding central/peripheral
I modified the code to change the quantization level of the I and Q data received by the receiver...
hardware:nrf5340dk
case: Bluetooth: Direction finding central/peripheral
I added CONFIG_BT_DF_VS_CONN_IQ_REPORT_16_BITS_IQ_SAMPLES=y in the direction_finding_central...
Hello Team,
Just to give you a background , I am working on a project using the NRF Connect SDK and want to run my application from external flash memory. Specifically,...