I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”,I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
I have been trying to interface the Witmotion WT901 sensor with the nRF5340 using the I2C interface. I have previously run the exact code on the nRF52DK and it was working...
Due to the allocation of Flash resources, only 100KB ROM for the app , and if we use Keil, we will have about 20KB of margin for additional code development, but we have to...
I'm new to Zephyr and have inherited a project that uses the stm32 h747 disco board. The last build shows:
Memory region Used Size Region Size %age Used
FLASH: 363268...
I'm trying to download a largish file (~167KB) via HTTP/TCP/IPv6 but the modem crashes every time around the same point during the download. It's spits out error 122, which...
Hi,
I just ran into a strange issue and traced it back to a KCONFIG problem... It seems that if I have BOOTLOADER_MCUBOOT and SECURE_BOOT configured "y" I end up getting...
Hello,
I' have problem with CMAKE and Zephyr in VSC. Please, see following error:
[main] Building folder: blinky_13
[main] Configuring project: blinky_13
[proc...
hi,all
I Need add many characteristic with notify in one service,and I wish it can send notify to the phone once the phone enable cccd.
1.tx_handles can work,buf rx_handles...
Good day,
I am developing app by SDK 17.1.0, including ble_nus and ble_hid, I would like to imply fuction to switch between ble_nus and ble_hid, due to some difference configuration...
Hi!
I am trying to subscribe to the power management events that correspond to the following log lines (which I can clearly see in the log):
I have been trying with this...
Hello All,
I'm currently now on the initial phase of development and i wanna to stream 2xIMU data through SPI as for now if i connect only one IMU as Follow
P1.15 SCL...
Dear all and Nordic Staff:
I am learning about dynamic multiprotocols and found examples of dynamic multiprotocols for Thread and BLE in the "nRF5 SDK for Thread and Zigbee...
Due to the system design of our products, I am going to need to sideload any firmware update binaries. That is, my application code will handle receiving the update through...
Hi
I am using ncs v2.3.0, mesh chat example
I have used CONFIG_BT_CTLR_TX_PWR_PLUS_8 =y , and it works quiet well, now how can i implement CODED_PHY (long range) in this...
Hello,
I came across a Nordic Q&A discussing a sample called hci_uart_with_usb_uart_bridge in this post . I have searched in the v1.0.1 tag but couldn't find the mentioned...