Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Hi,
I’m using a custom nRF5340 board , and I recently migrated my project from nRF Connect SDK v2.9.0 to v3.1.1 .
The same project compiled and worked fine on v2.9.0,...
Hello,
I'm interested in nRF54L10 SoC, in Mouser and DigiKey I see that I can buy it in this package: QFN48 (QFAA). However in the datasheet it shows this package QFN40...
Hi,
I’m currently working with the nRF54L15 DK using the Channel Sounding Initiator with Ranging Requestor sample from the latest nRF Connect SDK. The setup runs successfully...
Dear nRF experts.
I am using the radio_test sample with SDK3.10
We used radio_test to add UART commands to control the on/off of all GPIOs for pin verification. We found...
I'm currently looking for a high-speed data transmission and reception solution that requires wifi (NRF7002) throughput, but I don't want to transmit data via wifi. It should...
I'm using nRF Connect for Visual Studio Code, working on a project that has worked great in the past, but I'm getting error messages now when attempting to flash any board...
Hi,
We are using the PMIC in our smart ring where we have limitations of number of components used and specially the height of the components used. Here, the inductor...
Dear Nordic Support Team,
Hope this email finds you well. I am currently developing a Matter-enabled device using the Nordic nRF Connect SDK, and I’ve encountered a question...
Hi,
I just got a power profiler kit II and I want to use it in an battery based application, where there is also the possibility that current will flow in the opposite direction...
I am using the nRF54L10 chip with NSC-V3.0.0, and I encounter an issue when using uart21 (p2.07–p2.08). If RTT is connected, UART transmission and reception both work normally...
Why doesn't the scan_evt_handler get called in the ble_app_uart_c sample under nRF5_SDK_17.0.2_d674dde conditions? I've tried various things, but neither scan_evt_handler...
Hi,
We are testing a custom board based on the nRF5340 that drives an RGB LED strip using the TI TLC5947 LED driver.
The TLC5947 has an OE (Blank) pin that disables/enables...
Hello,
I am using an nRF52833 in a project where and i want to be able to update it via another mcu (STM32H7) over uart. The STM32 has received and saved the new hex file...
Hi, I have a custom NRF52840 board that I need to send EMG data via BLE with. Only has SWD, no usb-c data link unfortunately.
I am using version 1.6.1 of Adafruit NRF52...
I was reading the Errata document for the NRF54L15, and came across this: 3.18 [37] POWER: Current consumption might increase after pin reset or power cycle. So I was wondering...
