Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
hello Nordic
i work with nrf52832 as dispersed units and an nrf52840 dongle/ BL654 Laired which also has the nrf52840 as the central unit.
stage 1 - i need to transfer...
Hi,
Looking at the differences between S132 and S140 SoftDevice, I see there's lack of support for Long Range (Coded PHY) on the S132 (and S112 for that matter), which is...
Hello,
I am using the Thingy:91 PCB and I have disabled the nRF52 by cutting SB4 and soldering SB3. This makes me unable to log through UART. For this reason I implemented...
To the kind attention of Nordic support team,
I need to disable, enable gzll more times. When enabling it, code gets often stuck in my case as in figure: nrf_impala.c 442...
I have achieved Bluetooth connection between 1*ble_central<------>6*ble_peripheral.
But, ble_peripheral sometimes upload data at the same time, then sometimes lose data...
We're successfully using nrf_crypto_aead_crypt() with AES CCM, a 128-bit key, a 64-bit MAC, and the NRF_CRYPTO_ENCRYPT operator to encrypt some data and generate a MAC that...
HI, all,
I am trying to transfer my previous project from nrf51822 to nrf52840, and at very the beginning ,I can not make the UART/UARTE of nrf52840 work.
0, I have programmed...
Hi, everyone,
I am pretty new to nRF52 development. Right now, I have an issue with the SAADC trigger by RTC, which I follow this example . The issue that I have right now...
Hey all,
Here's another question. Many of the examples in the Nordic Connect SDK are rather large. Transferring them with MCUmgr at 115200 BAUD takes sometimes more than...
Hi
I am testing sending and receiving data between nRF51 dongle and peripheral by example of heart-rate-collector.
now I could find characteristics I need(write, read...
Hi all,
My application is as follows:
I have an android app which will send some data to a nRF DK. The data I want to send is in HEX characters between 0x00 to 0xFF. And...
Hello,
For nRF51822 and nRF52832, I'm using GPIOTE, PPI and timers to measure the duration that a pin, which is normally low, goes hi (typically 100-300 milliseconds). I...
The following questions are in regards to the instructions at nRF_Connect_SDK-modifying-a-sample-application .
In the Windows environment, I am transitioning from using...
