Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
We have a problem where a display running on 5V with an UART on 3.3V will self-bias through the UART TX pin when the 5V supply is switched on.
How do you make zephyr not...
Hi,
We are using nRF5340 DK and the nRF Connect SDK Version 2.6.1.
We are developing a mesh network. Our requirement is the one device can connect to three other devices...
Hello.
What is correct way to use AT%MDMEV commands(searh status) to establish connection after long PSM/sleep time (168h). Our devices are used to track wild animals so...
Hello,
I'm encountering persistent address conflict issues within my Nordic project.
Occasionally, when a device joins the network, I observe address conflict errors....
Hello,
I am trying to send an array which has 2048 bytes via UART. But, when I add a some delay to repeat the the UART transfer, the code gets stuck on the HardFault. I...
Hi Community,
I report this issue in github, it seems nobody reply me, so I ask here again.
lesson 8 exercise 3 solution build failed · Issue #9 · NordicDeveloperAcademy...
Hi,
in our application we use SDCard and USB stack with the following configuration:
The communication with the nRF5340 is done by using a Linux Embedded systems. When...
I think that the source of the nRF5340 Audio DK sample board is designed so that LED1 lights up when a connection is established with CIS.
We are thinking of connecting...
Hello,
I am using the ADC on my custom board, based on nRF9160.
I am getting correct results when measuring a known voltage. However, I noticed that the execution is very...
At the company I work for we are developing a keyboard with mouse capabilities via USB and BLE using the NRF5 17.1.0 SDK. We create the USB HID with the following SDK macro...
When using the nRF9160-DK, I flash the board with Asset Tracker V2 as provided by the instructions for the board here .
The board and SIM card are registered and the board...
Hi,
I am using custom board (nRF9160) and zephyr V2.6 and I would like to make sure that I understand the ADC settings correctly in the device tree:
channel @ 1 {
...
Hi there,
I have just tried to migrate to a new M2-based mac book pro and everything went OK (i am able to build and run my sw on the target) except that I don't have any...
hi support team，
i was testing smp_svr, i want to add button to my application that once i press the button and reset, the device will stay in mcuboot (serial port mode...
Hi,
I added build a conf to my project which has a prj.conf and select board. But the extension overwrites my configs with cache and extra cmake flags, which i dont want...
