If some one else have trouble that the Nrf52840 Dongel do not mount using cdc acm on openwrt this will most likely help.
First number is the verdor id second is the product...
Hi,
I am using "asset tracker" project in nRF9160 DK.
I want to update asset tracker application through HTTP.
So i migrated changes of "asset tacker" in main function...
I have a simple TCP client application running on the nRF9160. After connection to the server, recv is called and writes the data over Segger RTT channel 1, where on the host...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
I am currently struggling with a problem where Im trying to implement the internal fds module which always leads to hard faults as follows:
There is probably something...
Hi,
I read the link https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.9.1/nrfx/drivers/twis/driver.html and updated periodic_sync example as attached below.
But I...
We are trying to compare the accuracy of received coordinates and satellites using GNSS firmware on two devices: 1) nRF9160 DK with external antenna; 2) Our custom board with...
Hi,
Mesh SDK: v5
Using nRF 528232
I had implemented the Low Power Node example from the SDK and found that the current it consumed using a 1000mAh 3.7V battery was around...
Hello,
Scenario:
2x nRF52833 - One set as PTX and the second PRX. PTX is connected to my PC via UART. Both boards are initialized with ESB_PROTOCOL_ESB_DPL.
I want to...
Hello,
I am using nrf5 SDK for thread SDK for development of my thread based product. Product is already developed just have to integrate dfu in it. Few months back when...
Hello! I tested the ST BLE Sensor sample on my nrf52840 DK. It works fine. How do I view the logs? I installed the toolchain and Segger on Windows. I am following this doc...
I use my own programs and routines nrf5_ SDK_ 17.0.2\examples\ble_ peripheral\ble_ app_ hrs\pca10040\s132\arm5_ no_ packs Product Bluetooth broadcast cannot be searched Android...
Hi,
Using the Peripheral LBS sample, is there a way to add advertising data to use both the UUID and name?
I assume this is to be configured in the bt_data ad declaration...
I am using UART on the Fanstel BLG840F to communicate from the 9160 to the 52840. So far I have successfully been able to communicate from the 52840 to the 9160 but have not...
Here we go again .... I did read many posts in this forum but did not find an answer.
We need to CE test a small Bluetooth HID keyboard for a special use case. Our test...
I am running into the exact same issue described here: https://devzone.nordicsemi.com/f/nordic-q-a/53693/how-to-flash-application-after-dfu-bootloader/217434#217434 Basically...
Hi, Nordic Team
I’m getting started trying to use both MCUboot and NSIB for 2-stage secure boot on nRF9160, and use SEGGER as developed tool. I enable NSIB via “Configue...
Near as I can tell from v1.7 of the product specification, these two parts have the same footprint & pin-out because they're both aQFN packages (as indicated by the "QI")...
