Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
example: peripheral nus device: nrf52832(Self-developed board) hi i run the example peripheral_nus , but it cannot work. Though i had set the RC clock. But when i run the...
Hi, I am developing a product that has a nRF52840 as the main MCU and it controls a Quectel BG95 (a LTE-M/NB-IoT module, powered by Qualcomm's 9205 LTE modem) using Zephyr...
Good Day,
Im a developer in switzerland using the nrf9160 trying to connect to the nrf cloud using mqtt, i have already flashed the credentials, updated the modems firmware...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
Hi all,
In Device Manager, my nRF52840 DK is recognized as follows:
JLink CDC UART Port (COM32) JLink CDC UART Port (COM33) USB Serial Device (COM22) — running a Zephyr...
I'm looking to use the new Zephyr support for the ProMicro nRF52840 board, which appears to be available in NCS v3.
However, Zigbee R23 only appears to target v2.9.0.
...
Dear devzone support,
I have a quick quesiton.
Why does the nrf5340_audio application only support 1 BIG, while the nrf_auraconfig support 2 BIG. Is it because of using...
Hello,
I'm adding power management to a custom driver that talks to a sensor via uart2 of the nRF9151DK. But from my tests it seems that uart_irq_rx_enable() has no effect...
Hi all,
I've got an existing OpenThread project for my workplace's metering product which currently is written for a TI CC2538 and I'm porting it across to run on a nRF52840...
Hi, I have a custom board with nrf54l15 and it does not have a 32 kHz crystal, it only has a 32 MHz crystal. Sometimes the code gets stuck at this line: Can it be related...
I have a peripheral which has an nRF53. It connects to either an Android of iOS phone. I've been testing add Connection Subrating. However I've been noticing that the Connection...
I have an NRF9160 system running and I see mention of " The nRF9160 PWM peripheral can capture the period and pulse width of an external PWM signal" but was a little confused...
DeviceTree Visual Editor shows SPI1 as enabled, but the changes are not reflected properly in the GUI or in build behavior.
I receive the following build error : " DT_N_S_soc_S_gpio_50000000...
The nPM2100 datasheet (v1.0) provides Figure 8: Load current triggering mode change vs. VOUT.
Can you confirm:
1. Consider the system is in Low Power mode. If the load...
Hello,
I am trying to implement OTA through BLE, and as Im building the program, Im getting a build error as :
error: 'FLASH_DEVICE_BASE' undeclared (first use in this...
