Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello everyone!
I want to form an Openthread network with three Nordic nRF52840 cardboards. I would like to monitor the traffic using a sniffer, but i can't receive any...
We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi.
I'm using nrf52832 with SDK-17, and the ESB example (esb_tx and esb_rx)
I'm not much experience in nrf development recently I have a project related to ESB to transmit...
Hello,
In nRF52832, we use nRF Connect to read the board, save the program data into a hex file, and send the file to other developers. They can use nRF Connect to write...
I am using sniffer v3.1. I have installed the sniffer code on a nRF52840 dongle (PCA100059). When I insert this into the PC with windows 8.1 it appears as "nRF Sniffer for...
Hello,
In our product, the nRF9160 is configured to use LTE CAT-M1 and we are measuring the signal quality thorugh the AT+CESQ command.
After begin registered on the...
Hi: I have write a spi slave, and write a spi master on STM32, It can receive data from STM32,But I have no time to prepare the response data.
as the code below, I can receive...
I checked the SPI communication using the NRF52832 development board.
Based on the firmware of the previously developed NRF52810 product, the SPI operation code is applied...
Would like to interface a SPI ADC – MCP3461 via the nRF52840 serial peripheral interface master with EasyDMA (SPIM). I was not able to find whether or not there is an available...
Hi Everyone,
My issue is mostly stated in the subject, I hope someone can help me recover this DK because as of the moment this is my only way to program/debug out EVT board...
I have nrf52833 as Tx. Ialso have nrf52833+ antenna array as Rx. I want to send CTE data, implement IQ sampling and view AOA for implementing direction finding. Kindly assist...
Hi,
I'm considering shifting to SES (from VS-code) to get debug capabilities.
(Zephyr application developed under NCS tag v1.5.1)
I tried to import my project doing...
Hi
I am developing a Zephyr application on a nRF52840.
Is it possible to runtime change pinmux. Eg. I have set rx/tx for an uart to p1.8, p1.9 and want them to be changed...
Hi nordic,
I want dfu the BL only, how should I pack file? Can show me how to pack instructions of nRF Util, only update bootloader.
Thanks and best regards!
John
Hello,
I am using nrf51822 / SDK v12.3 / SD 130.
I want to change the FW of the sold product to a new FW.
The bootloader address / length of the two are the same,...
