Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
Trying to migrate from SDK v2.7.0 to v2.8.0 and suddenly getting the build error
Based on other forum posts, I was able to track down more information using the <build target...
Hi, I just got two nRF52840 dongle and it works great as BLE sniffer.
I want to send continuous BLE data (not only advertising) packet and sniff packets between bonded devices...
Dear Nordic Team,
I am currently working with the nRF5340 DK and would like to know whether it is possible to read or retrieve the Network Core firmware version directly...
Hi,
I am using NCS 3.2.1 and nRF52840-DK's version 3.0.3.
I flashed 2 boards with the openthread/cli sample.
From the CLI on both boards, I issued the following commands...
I’m trying to transmit a payload of up to 2,450 bytes using CoAP over OpenThread. Before jumping into firmware development, I want to evaluate the feasibility of transmitting...
Hello DevZone,
I have some questions about nPM1300. I know that nPM1300 need a battery pack that already contains a PCM.
When the PCM activate the protection due to overdischarge...
Hi,
I'm using the nRF54L15 (custom board, nRF54L15 DK base) with NCS v3.1.0.
I have two UARTs:
uart30 — Shell/console (needs CONFIG_SHELL_BACKEND_SERIAL=y , which...
Hi,
I'm trying to use an nRF5340 Audio DK to communicate with another board via SPI. The voltage needs to be 1.8v. How do I configure my board to do this?
Hi,
We are using the nRF7002-DK board. I am using Zephyr samples/net/wifi/shell with no other external connection other than the j2 micro-usb connection to PC and with the...
Hi,
We're aware of the modem 2K TLS buffer limitation. It's causing us quite a bit of headache related to the device shadow.
Our application needs a number of config parameters...
Hello,
I am trying to access to two partitions of 2gb each on a micro SD card of 32gb.
I can access to one partition of 32gb in my micro sd card but as it is formatted...
I've been struggling with Thread connectivity on a custom PCB, powered by a MinewSemi ME54BS03 module (with IPEX connector)
I'm using an external 2.4GHz antenna and I'm...
Hi,
I am facing a power consumption issue with the nRF54L15 (BM15C SoC) in deep sleep (System OFF / low-power state). The measured current consumption is approximately 221...
Hi all,
Note that I am using a Fedora Workstation VM on VirtualBox for keeping everything clean. I pass the connected USB development board to the VM. I am trying to evaluate...
