Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Looking at the datasheet for the nrf54h20 it lists GPIO port P9 as Slow and Analog.
However, in the pin mapping, it also says SPIM130 and SPIM131 are available on port...
Hello,
We are trying to run 802.15.4 alongside our BLE Mesh network on the nRF54L15.
However whenever compiling with CONFIG_NRF_802154_RADIO_DRIVER =y, we run into the...
Our peripheral medical product, based on the nRF5340, is designed to pair and bond with both PC and mobile devices via Bluetooth Low Energy (BLE).
I've implemented BLE Security...
Hi,
I'm developing a custom MBR/bootloader for NRF52811 which is used as a second/radio MCU on the board. The MCU will need to run applications with and without the softdevice...
Hello,
I see that the nRF54L15 recently had a datasheet released at v1.0. Is there any difference between this and the preliminary v0.9 datasheet? I cannot seem to find...
Hi,
SDK 3.0.2, nrf9160 (actinius icarus som), custom board, based on modules example. LTE-M with PSM.
Floor current is too high, at around 500 uA. There is a known issue...
Hi,
I am looking to create use a pm_static.yml to create a partition table for MCUBoot, which have the internal flash as the primary boot partition and the external SPI...
I get this error after creating a custom board
C:/ncs/v3.1.0/nrf/subsys/mpsl/init/mpsl_init.c: In function 'm_config_clock_source_get': C:/ncs/v3.1.0/nrf/subsys/mpsl/init...
I'm attempting to put together an application using the baremetal version of NCS just released... I need these to run DFU over BLE so we can update in the field.
I created...
Hello,
I am experiencing a recurring issue when programming multiple nRF52840 boards using the nRF Programmer.
Problem description: When programming the first board...
Hello, I have a pin that controls the power flow to the sensors on my board. it is active low, when it gets a raw value of 0, it allows the power flow to the sensors. I have...
I have just upgraded my project to NCS 3.1.0 and I'm now getting this error
BOOT_SWAP_USING_MOVE (defined at C:/ncs/v3.1.0/bootloader/mcuboot/boot/zephyr/Kconfig:575) set...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hi, I am working on storing data in the Trusted Zone using the PSA APIs.
I tried the Protected Storage (PS) example. When I store data using psa_ps_set() and then read the...
