Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I'd like to update a firmware which is essentially made of 2 parts, say 0x1000-0x8000 is a "read-only" part and 0x8000-0x50000 is a "read-write" part. If I flash this firmware...
Hi Nordic Team,
Is there any way to input 3 audio streams (through I2S ) on nRF5340DK board are there any extra I2S Port available to input one more sinusoidal signal and...
Hi,Team,
I am developing Pawr using nrf54l15-dk.
For the Pawr example I refer to E:\NCS\v2.8.0\zephyr\samples\bluetooth\periodic_adv_rsp and periodic_sync_rsp.
I want...
Hi, I'm following the Academy lessons and just tried to get the Blinky sample to work with a nRF54L15DK. I can see on a serial terminal that the code is running and console...
Running the WiFi scan sample on a Thingy91X or NRF7002DK in SDK 2.8 and 2.9 works for scan_done results but if you change to show raw scans, no raw scans are displayed. The...
I have a custom PCB that has been working fine in terms of the Wi-Fi on 2.6.2 but I needed to Port that to 2.9.x I'm using sysbuild in the 2.9 projects but not in the 2.6...
Hi Support Team
The VDD of customer’s nRF54L15 board is 3V, but the high voltage of P1.10 is about 1V. Did you meet this issue before? Customer needs the output high voltage...
Dear Nordic Team,
I am currently working on a project that integrates your HTTPS client sample with your BLE provisioning sample, specifically on the nRF5340 with the 7002EK...
Hi,
I am testing the Bluetooth remote discovery of the nRF52840 in LE Coded mode with the transmission power set to 8 dBm.
The farthest distance currently achievable is...
Hello, I have developed a module using 54L15 and am currently measuring its RF performance. On Rohde & Schwarz instruments, I have observed numerous test results regarding...
Hi guys, I am using the SDK v2.9.0 and the toolchains b620d30767. To add the build configuration for the sample peripheral_uart, the console print some error log.The log as...
Hello.
I am trying to follow Downgrade protection using MCUboot to enable Hardware-based downgrade protection. However, an error occurred, and the software did not start...
I used the battery routine to test the ADC, and the voltage measured was 3 times larger.
How to fix this problem？
Bat+ is 3.3 V.
dts setting:
vbatt {
compatible...
Hello,
I'm looking for an existing Android/iOS Flutter DFU library that supports nRF5340.
I found this one: https://pub.dev/packages/nordic_dfu but with limitations to...
Hi there I am using nrf5340 for my project. As per the datasheet , it has 1MB flash memory for application core and 256KB for network core. what i want is to merge the network...
