i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
hi,
I used nRF52932QFAA ,SDK14.2 uart bootloader.it works well with softdevice loader 5.0.0.But when I download my app(without softdevice),it cannot work.
Flash composed...
Hello Noric Dev Zone members,
we are looking for a Firmware developer supporting us in bringing Hyko to our customers.
What we are working on is making energy heroes in...
Dear Devzone:
I have setup done matter environment as blow:
NB: Ubuntu 22.04 with WIFI and BT, installed CHIP tool from official pre-built (V2.8.0 corresponding version...
Hello
Our customer makes IoT Product and use the Nordic 9160.
However the PCB Size is small.the 9160 SiP design in the PCB Top layer and Sim Card design in the Bottom...
Hello
As the title says, I am suspending the UART using PM_DEVICE ACTION_SUSPEND, but the power consumption is not decreasing significantly.
With CONFIG_SERIAL=n and no...
Hello. I'm trying to toggle a GPIO pin at a predefined frequency in order to measure the accuracy of out RTC clock. This code uses the GPIOTE, RTC, and PPI peripherals in...
We are evaluating the the NRF 5340 for a new project and we would like to know if the NVS implementation [1] provides protection against data corruption if the supply is unexpectedly...
Hi guys,
So, I've been working on a project for measuring liquid using the TDC1000 IC from TI which was running fine on STM32.
My experience with nordic connect sdk is...
Hello~
I am developing nrf52840 with zephyr ncs tool chain v2.7.0 and SDK v2.6.1.
Our pre-production PCB power consumption still too high, so we are looking for a way...
Hello, I have a Thingy:53 sensor hub application (extended the Nordic Thingy53 Sensor Hub blog to include IAQ sensor) built under NCS v2.7.0 that runs fine.
When rebuilding...
In the link process between Central and Peripheral,
sometimes Link processing does not work correctly and the following log output: . cis_gateway: Discovery failed: 14 ...
1. After DFU has successfully completed the watchdog fires. I know this because my App picks it up from the register, however I'd like to use this bit to indicate a potential...
Hello,
I am designing a PCB using the nRF54L15 and a ceramic antenna and got confused regarding the impedance-matching network. In the detasheet a 1.5pF, 2.0pF, and 0.3pF...
Hello,
I am using nrf52832 as a peripheral and running SD S132. l am looking for an ble peripheral example wherein the Out of Band security level is used.
Can you point...
Using Programmer v4.0.1 can successfully read the NRF51822AB, but upgrading to the latest version 4.4.2 results in a failure to read the device.
Additionally, after...
We are working with nRF52840 and NCS2.6.1. And we want to change pin configuration for UART1 instance during the runtime and we have also used following ASYNC UART configuration...
Hello,
I am trying to upload certificates to my nrf9160 chip on a custom board. I have done the following: 1. Loaded AT_CLIENT from the samples
2. Tested all AT commands...
