Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
hi,
I used nRF52932QFAA ,SDK14.2 uart bootloader.it works well with softdevice loader 5.0.0.But when I download my app(without softdevice),it cannot work.
Flash composed...
Hello,
I'm working with Zephyr and using MCUBOOT as bootloader.
Due to HW design I have to set and hold a gpio as fast as possible when the application boots (to prevent...
Hello,
We're seeing an error that only happens after a cold reboot (unplugging the battery and replugging it) and it happens inside the bootloader while trying to open the...
Dear all:
I used this command to build light switch for 5340DK:
west build -p always --build-dir nrf/samples/matter/light_switch/build -b nrf5340dk_nrf5340_cpuapp nrf...
Kconfig failed: [Errno 22] Invalid argument: 'c:/users/user/zephyr/kconfig"' is an error that appeared this morning. What is supposed to be in the Kconfig file. I have been...
I can't remember where I found it now, there was a file somewhere that listed all the files in a project. It had
absolute paths which filled me with dread as it means a...
Hi
I am working on a custom board and have hit an issue with the software part. When the nrf_modem_lib_init function is invoked, it always ends with a timeout (errno ...
Got a Thingy91 (not the x model) that doesn't show up as anything when connected to a PC by USB, except when in bootloader mode, by pressing SW4 (no reaction with SW3) when...
I read other similar issues on this forum but they haven't helped solve my problem. I started with the peripheral_uart example project. Development and execution on the target...
Sorry for long sentence. The nRF5340 document describes about the Reset. This chip set have the POR. so, if POR function work, I don't need to use the PIN reset. because POR...
I have configured my application according to the Throughput example. The prj.conf file inside the sysbuild\ipc_radio folder is not being considered in the build. As a result...
Hello, everyone.
I would like to use mcumgr to update the firmware of a nrf52 via another nrf52 over uart.
From the documentation I understand that smp supports uart so...
Hello,
I just got started with the nRF5340 DK. I went through the example which instructs how to load the "Blinky" applications, build it, and then flash it to the Board...
Hi! I am trying to get OSDP communication up and running on my nrf9160dk board. I am trying to run this sample: https://github.com/zephyrproject-rtos/zephyr/tree/main/samples...
Hello,
I apologize if this is a simple question. I am working with the nRF9161-DK and am using the Serial LTE Modem application. The ultimate goal is to send data via...
I'm working on a Matter 1.3-compatible door lock with RFID credential management. I’ve enabled RFID support through the ZAP tool and configured the feature map accordingly...
