Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Dear DevZone,
While porting our project from NCS 2.9.1 to NCS 3.0.0, I ran into linker errors when building LVGL. The linker reports that it cannot find functions defined...
How do I map the build codes noted in the Rev Errata to the stamps on our ICs? I have two versions with QFAAAB and QFAABB stamped on them but the documentation says QFAA-B00...
I'm developing my product using NCS. It compiled fine yesterday, but today when I opened VS Code with the nRF Connect extension, it prompted me to install the toolchain. I...
Hi,
We have some GPIO pins where we want to change their configuration during runtime. We want to switch them between input pull down and output. Is this possible?
When...
Hello, I want to disable parts of my RAM to save power. I implemented this in my project based on the System_Off ram retention example. I'm now not sure if RAM retention is...
I noticed that the product information of the nRF54L15 series kit supports 4Mbps, but I'm unsure how to verify it. Are there any relevant examples available? I have currently...
Dear Nordic Support Team,
I am experiencing difficulties flashing firmware to my nRF52832 development board using VSCode with west flash , followed by J-Link...
Hi, We are using nrf Connect SDK 2.4.0 and have been looking through the NIST vulnerabilities databases. One of the vulnerabilities reported with the nrf5340 is a denial of...
Hi,
I am using nrf52832dk board for test nus service with ncs2.9.0, but I am facing some problem with MTU setting.
I found a configuration item "
CONFIG_BT_L2CAP_TX_MTU...
My application is based on the ncs nrf5340_audio application, but my application and hardware target are both out-of-tree and I am using ncs v2.9.0.
I am able to connect...
Hello,
I have a firmware that sends every 15 min a packet to nRFCloud using nrf_cloud_coap_json_message_send().
The code is working great most of the time : hundreds of...
Hi.
We have a device connected to Azure IoT Hub with telemetry interval set to 10 min and on interupt. Tried changing interval to every hour, but then it looses connection...
I've tried the following with the Quick Start app v1.2.0, v1.1.0 and v1.0.1. The log below is from v1.1.0, if I recall correctly. All logs are about same. Programmed the Asset...
Hello,
I'm trying to enable RTC2 for nrf52840 DK to use as a date time clock and set/get over SMP protocol. RTC0 is used for MPSL, RTC1 is used by the system.
I configured...
Hello Team, We are currently using the nRF52833-QDAA-R SoC for our R&D activities and have assembled the board based on Configuration 6 . However, we encountered an issue...
