I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
I'm trying to send a saadc float value over ble (dk to dongle) with ble_nus. I'm getting the right values but also some other stuff in addition. How can I filter this...
I need help with the minimal circuit board requirement of the custom board with nRF52832 and nRF52840 for wireless and SPI communication.
I need to read vales over wireless...
Hello !
Do you have any evaluation results for nRF21540 DK in case of real connectivity range ? Just some typical digits what can be seen easily.
I have own radio and...
I am trying to setup and run the existing scripts, which are part of pc-ble-driver-py.
The following are the steps and tools
1. Installed the pc-ble-driver-py pip install...
i m using nrf5340 cutom board, so i m using rtt logging method using jliink rtt viewer , to see logs .
so, when i am going to project section at top in embedded segger studio...
Hi,
I have a custom board with nRF52840/SDK 16/Softdevice 7.3.0 using Secure Dfu Bootloader. On my Android device I use Nordic Dfu Library. I have tried all available Dfu...
Ever since the toolchain manager v1.0.0 came out in the nRF Connect software, I have been unable to download it. I keep getting this error:
Any ideas?
Thanks,
Jow...
Hi
I am using SDK 1.9.1 with VS Code on MacOS to develop for nrf5340. I also have a nrf5340-DK board.
I am having problems finding the right includ file for using the...
I'm new at this (so be gentle). Trying to understand the process for activating a SIM card with Verizon using the NRF9160. I see that this modem is approved; so do I only...
Hi, I want to add CLI in our current firmware. i found a way to do is Zephyr shell. our firmware is based on aws iot sample and nrfconnet sdk1.9.0 after integrating zephyr...
According to data sheet of nRF52832, internal pull up resistance is 13kohm. Can we find the 13kohm internal pull up resistance in the code and can we change that internal...
Ideally we should not get any data when internal pull up resistors of nRF52832 board are disabled and external pull up resistors of SHT 40 Slave sensor are disabled. But I...
Hi,
I haven't been able to actually find out if the VBUS can be used to drive the DETECT signal to go from system off to on mode.
Are there any examples on how to configure...
Hello All, We have designed a custom board for our product and everything pretty much works fine. But now that we have decided to stick to WebBLE, we are facing some issues...
Hi,
I would like to declare my pin in output open-drain, so i use this configuration
My issue is when i declare my pin, I have an unexpected low state that occur...
