Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi all,
I have compiled the ble_app_hids_keyboard example for a nRF52832 on a Laird DVK-BL652 breakout board.
I have a tablet running android 5.1.1 and the nordic nRFConnect...
Hello All,
We are using nrf52840 board interface with wiznet550i.
We try to implement mqtt tls 1.2.we get following errors..
I get certificate verification error -0x2700...
Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Hello,
I' have problem with CMAKE and Zephyr in VSC. Please, see following error:
[main] Building folder: blinky_13
[main] Configuring project: blinky_13
[proc...
hi,all
I Need add many characteristic with notify in one service,and I wish it can send notify to the phone once the phone enable cccd.
1.tx_handles can work,buf rx_handles...
Good day,
I am developing app by SDK 17.1.0, including ble_nus and ble_hid, I would like to imply fuction to switch between ble_nus and ble_hid, due to some difference configuration...
Hi!
I am trying to subscribe to the power management events that correspond to the following log lines (which I can clearly see in the log):
I have been trying with this...
Hello All,
I'm currently now on the initial phase of development and i wanna to stream 2xIMU data through SPI as for now if i connect only one IMU as Follow
P1.15 SCL...
Dear all and Nordic Staff:
I am learning about dynamic multiprotocols and found examples of dynamic multiprotocols for Thread and BLE in the "nRF5 SDK for Thread and Zigbee...
Due to the system design of our products, I am going to need to sideload any firmware update binaries. That is, my application code will handle receiving the update through...
Hi
I am using ncs v2.3.0, mesh chat example
I have used CONFIG_BT_CTLR_TX_PWR_PLUS_8 =y , and it works quiet well, now how can i implement CODED_PHY (long range) in this...
Hello,
I came across a Nordic Q&A discussing a sample called hci_uart_with_usb_uart_bridge in this post . I have searched in the v1.0.1 tag but couldn't find the mentioned...
Hello,
I'm attempting to establish communication between an nRF52840 and an nRF9160 on the nRF9160DK using LPUART. Initially, I tried using the interrupt-driven mode, but...
I get the registration "parse_cereg: LTE mode not found, error code: -22" error,when try to connect to LTE network in china shenzhen.the hardware is custom use nrf9160 chip...
sdk 2.1.0
nRF9160
Hi, I need to parse a JSON file and for that I'm trying to use zephyr's json.h library. Based on the automatic test file I built a piece of code for...
Hi,
I am trying to use an ST7789 display with the NRF9161DK, I was following this guide but got no luck:
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b...
Hi,
I was looking into hooking up an SD card to the nRF9160DK that I use for data collection during evaluation and early stage pilot projects. I noticed that there is an...