Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi,
The attached screenshot shows a section of an air-trace for the 5340 running a commercial LE Audio stack. From the rising edge of the logic inputs, it can be seen that...
Hi List, I am using ZMS to log data. While performing stress tests, I see few issues:
Including zms in the projects makes the application boot time delayed. The delay...
Hi there,
Several examples of the course include a configuration file and an overlay file for the nRF52840 dongle. However, the code cannot be compiled. The problem seems...
Hi everyone,
I’m trying to use the HTTP client sample from NCS v3.0.2 with a W5500 Ethernet shield on an nRF5340. DHCP works fine, and I can successfully POST and GET using...
We are using the Murata Type 2FR dev kit - https://www.murata.com/en-us/products/connectivitymodule/wi-fi-bluetooth/overview/lineup/type2fr
Internally, this has NXP's RW612...
I'm running the subrating sample (ncs\v3.1.1\nrf\samples\bluetooth\subrating) on two nRF54L15-DK boards. Using a protocol analyzer I'm seeing that when the subrate factor...
Hi there,
Just a minor flaw in the exercise, but a question concerning the callback from the event “le_param_updated”. In the solution to query the connection interval,...
One of my customers currently has a requirement similar to the one discussed in this ticket:
In their product, the main controller is a BES2610, and the Bluetooth functionality...
Hi
According I2C standard, there is a requirement regarding falling speed of SCL/SDA which is > 20*1.8/5.5=6.54ns, and our measurement result of Tf on SCL is 5.732ns.
...
Hi
I am using the nRF7002 DK with NCS 2.7, based on the sample project `nrf70-wifi-ble-image-transfer-demo`. I modified the code to embed a fixed image as a header file...
Hi
In nRF5340 datasheet I2C frequency only have 4 selection as below
But when ask your AI, he response below
Important errata at 400 kHz
For all nRF5340 revisions...
I would like to trigger a hard reset when valid voltage is first detected on VBUS. How could I do this with no or minimal external components and without a complementary MCU...
We are using the nRF54L15 SoC with FOTA functionality. We have enabled secure FOTA by signing the firmware image and provisioning the public key into the SoC’s KMU. For production...
I'm running the subrating sample (ncs\v3.1.1\nrf\samples\bluetooth\subrating) on two nRF54L15-DK boards.
I'm puzzled by something I can see through my protocol analyzer...
