Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Hi all,
I have an issue when trying to use the fstorage without the SoftDevice. The documentation explains that it is possible to use the FStorage without SoftDevice if...
Hello,
I have nrf52832 development board with PCA10040 version 1.1.1. I can build my code correctly and I can erase my chip from Keil uvision but when I try to download...
Hi,
I am trying to interface OLED(SSD1306 driver) module/break-out with nRF52840 D.K, PCA10056 1.0.0 but it's showing some noise/dots/garbage. Code: nRF5_SDK_15.2.0_9412b96...
Hi all. I want to add ssd1306 controlled OLED display with SPI to my project how i can hook up u8g2 library or another library for OLED display to nRF52832.
My application requires ultra-low power consumption, hence the nRF52810 will operate in low power - RTC running from LFRC clock, full RAM retention (1.5uA current spec'd)...
Hi,
I really would like to be able interface with the modem at the lowest possible level. I got the bsdlib working.
I use the following procedure to send AT commands and...
Hi Nordic,
We are having a Finger Wearable Unit(FWU) based on nRF52832.We are using JLINK Base Debugger to debug the FWU.We are able to debug and get the debug logs when...
Hi. I have built an ble application which runs on the nrf52832 with softdevice S132 V 6.0.0. In addition to the application and the softdevice I program a bootloader on the...
Hello,
I am learning bluetooth mesh with Light switch demo example. I have downloaded the folder "nRF5-SDK-for-Mesh-master" from the link "https://github.com/NordicSemiconductor...
Hello all!
We have custom HID with multitouch BLE device. We took HID descriptor from USB where this works pretty good, ported it to BLE and it seems not working as expected...
I just upgraded to nRF Sniffer V2.0
The Time column of Wireshark shows wrong values for short delta times. Is is set to "seconds to previous packet"
My advertiser runs...
Dears,
I have a problem with the ble_ant_app_hrm in the examples (multiprotocol). I am using a pca10040 demo board with sdk 14.2 with IDE SES on a MacOS
I have flash...
Hi, I'm using nRF52832 with SDK 15.2 and 3.0 (Mesh). when I try to provision 2 or 3 client/servers the nRF Mesh application behaving properly which means provisioning is happening...
Hello,
I would like to use an usb dongle with nRF52840 above and
- on bluetooth side give an spp or vsp profile
- on usb side be an usb cdc device
the reason is: I...
Hi,
We are currently implementing a mesh application that is expected to have a large number of mesh devices. We have already tested DFU on a smaller mesh and it is working...
