Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi
I need to reball some aQFN73 nrf52840 devices and I couldn't find the specific ball size in the product spec document Nano_BLE_MCU-nRF52840_PS_v1.1.pdf
Can someone...
Hello,
We are currently working on a project where we need to sample a frequency input on a GPIO pin up to 6MHz. I have tried GPIOTE and TIMER with a PPI channel, but can...
Hi! We are currently in the process of migrating our nrf5 SDK code to NCS, on nrf52833-based hardware. After being stuck for a while on the basic init process of MCUBoot,...
Hi
I am reading the exernal power in one ADC channel and the backup battery in other ADC channel. When my hardware has not external power and the backup battery drop until...
We have some devices that run the same firmware, but need different default BLE tx power settings.
There is a KConfig value to set the default, but in our case it is different...
Your old documentation website ttps://infocenter.nordicsemi.com/ carries a banner saying it will be shut down on 18 June 2024. Please don't do this! I can't find equivalent...
I'm running NCSv2.6.0 on some custom hardware, with an nRF52832 IC fitted. I'm trying to trigger an ADC measurement every ~ 300usec using a Counter, so need to set the Counter...
Hello community,
I am working on a custom nrf5340 board design, that uses the BL5340PA external antenna module to implement the nrf5340 chip in the design. The BL5340 module...
Hi,
I've attached the steps performed to install the mosquitto bridge and getting errors on yarn deploy
Also see attached steps, I believe I have done everything correct...
I have recently upgraded my SDK from NCS V2.2.0 to V2.6.0, and have come back to some firmware I had working under 2.2.0 as I need to progress that. The firmware is based...
Hello,
I just got started with the nRF5340 DK. I went through the example which instructs how to load the "Blinky" applications, build it, and then flash it to the Board...
You may ask what poolside means. It means at my community pool, where I don't have Internet access via Wi-Fi for my laptop.
I wish to run some AT commands like AT%NCELLMEAS...
Hi, I have followed the instructions in Securely generating credentials for nRF91 Series devices - nRF Cloud but cannot connect to nRF Cloud.
I think the instructions on...
I'm confused about the use of these two functions. I want my app to sleep immediately upon start and then wake up and do a BLE advertise when I press a button.
I...