hi dear nordic employee:
I tried to build the project ble_app_hrs_c(pca10040) by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit(nrf52832)
2、what is my purpose?
the quality of thingy52 audio demo is not good(iphone7)...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello,
In the nrf5340_aduio application. I found it support 2 channels both of output(mic signal) and input(audio signal) on the USB device.
But i want to know if it can...
Hi!
I use SDK15.0 and s132_nrf52_6.0.0_softdevice
I use nRF52 in two modes- peripherial and central in one time.
When I use it like peripherial and have connect with...
Hi,
I am debugging an application whth MPSL enabled and occasionally get this error:
E: SoftDevice Controller ASSERT: 48, 190
E: ***** HARD FAULT ***** E: Fault escalation...
Dear Nordic team,
I'm evaluating nRF5340 Audio DK for the use-case of broadcasting multiple streams.
Until now I've succeeded in broadcasting 4 streams (LC4 bitrate...
I download urfutil and install the nrf5sdk-tools in the Dockerfile
When running the image locally all is well, the installed commands are found.
But when it is running...
After interfacing my STM32 with the nRF9160-DK board and completing the programming, I now need to flash the board with the firmware update file, application file, and our...
Hi,
I noticed all of your DK have multiple UART over the USB port. I believe some are from the nRF91 or nRf70 etc and some form the Segger module.
For a new HW design...
what is the difference between internal oscillators and external oscillators for nRF52833?
What the functions are affected? can share more details so we can choose proper...
The sample source of unicast_audio_client and unicast_audio_server can be built with VScod or command line, but an error occurs when writing.
The error is as follows.
...
Hello, Im trying to use the Unity framework. I was able to run a simple test, however I would like to change the print function - UNITY_OUTPUT_CHAR . From the nrf/test/unity...
Hi
Is there a way to do this quicker?
I have my own custom characteristics. Is it like bonding will imrpove this? Atleast for the case of a reconnection?
Is it bonding...
Hello,
I am running a simple experiment to turn on all GPIO pins to active on the NRF52840.
The code attached works on the NRF52840-DK, and I am able to measure 3v on...
Just started another project using an nrf52840 dev board, and the printk() call produces no output. There is no output for Zephy booting, or anything else. I have tried both...
Hi,
according to my system architect it should be possible to use a standard https://github.com/NordicSemiconductor/pc-ble-driver on the nRF52840 Dongle for implementing...