Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi,
I'm working on a four layer PCB including the nRF7002 for WiFi location finding. After looking at the various Altium Design files available (Thingy91X, nRF7002Dk, nRF7002EK...
I want to test the nrf21540dk to compare range improvements over the nrf5340dk and nrf52840dk. I am using the hci_pwr_ctrl demo and want to adapt it for the nrf21540dk. I...
Hi — I’m working with two nRF5340 Audio DKs (one as server/gateway, one as client/headset). When the nRF5340 server uses standard BLE Audio (CIS/ISO + LC3) it connects and...
I am trying to get the hci_pwre_ctrl demo working with a nrf5340dk using nrfconnect 3.1. I got it running with a nrf52840dk and it works fine. I created a 2nd build for the...
Hello Nordic Support Team,
I am currently working with the Arduino Nano 33 BLE (ABX00030) , which features the nRF52840 SoC , and I am interested in accurately measuring...
I want to read the RSSI. The code is shown as follows: ，However, after compilation, the error message displayed is: "undefined reference to `bt_hci_cmd_alloc'".I need to know...
Hi there,
I am seeing inconsistencies with the PCB layout specification of the nrf7002.
1) In the v1.1 of nrf7002 datasheet, it is recommended that the following capacitors...
Hello, we are currently testing the output of square waves through GPIO output pins. However, I found that a single operation to set the GPIO output pin high or low using...
I've installed the same version of the Power Profiler V4.3.1 on Linux and on windows.
On windows the device gets recognized straight away and I can use it, on Linux however...
If I understand correctly, you can pretty much assign any pin to any peripheral. I've been using a modded central uart project on a dev board but on this other board I'm using...
Hello,
is there any way to access the Stack and Heap Start/End memory addresses from the zephyr code?
I have found the __INITIAL_SP definition that gives the Stack start...
Hi,
I have been working through the Dev Academy cellular course using the nRF9151 DK which is fitted with a 1NCE MFF2 eSIM. I was able to set this up in the Board Configurator...
Hello Team,
I am using the nRF52833 with the nRF Connect SDK (v2.9.1) in VS Code , and I am experiencing an issue with the RTC calendar update.
I initially set the RTC...
Hi everyone,
After a debugging session using the debug tool in nRF Connect SDK with an nRF52832 on a custom board, the chip is now completely unresponsive—I can't flash...
