I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi,
I have nrf52833-DK. Where should I get started for DOA applications? I'm experienced with other nRF chips, but not for DF and RTL applications specifically.
Hello,
I try to debug a BLE connection with the nRF Sniffer. As a test, I used one nRF52 DK (PCA10040) as peripheral using nRF Connect and and Android phone as central device...
I'm using the HID keyboard as the base example. We're using prototype hardware so the connection gets dropped periodically due to ongoing hardware issues. But this has exposed...
Hi, nordic Engineer!
Merry Christmas！ I am using the DF to develop my project and considering simulation with the Bluetooth signal with antennas to build a customized antenna...
Hi,
I am trying to receive messages via Bluetooth mesh and forward them via UART (using UART async API) on the nrf9160DK. But when I try this, I get an assertion error from...
Hi,
I'm using SDK17.2 to develop nRF52810's application.
When APP_ERROR_CHECK or APP_ERROR_HANDLER have a fault which is caused by hardware or software, the system will...
Hi,
I want to trigger a wake up from System ON sleep (WFE) using the LDETECT signal on Zephyr.
I managed to wake up using Zephyr's gpio API but my understanding is that...
1. Nrf52840 acts as central and Nrf52832 acts as peripheral. when nrf52840 has connected with nrf52832, nrf52832 disconnected occasionally. Disconnect reason 0x0013. When...
Hi there!
I have recently managed to combine sht85 with light lightness server code. J-link is able to produce 2 values (Temperature and Humidity) whenever I key in the...
I has successfully built the following demos and run them on a nrf52840 dongle (board: nrf52840dongle_nrf52840) :
cdc-acm-console demo from Samples and Demos » Various...
Hello,
I'm struggling with DeviceTree support in Segger Embedded Studio and nRF5340. I want to use the I2C Modul.
So I defined in my (dts)overlay file
&i2c0 { status...
Hello,
I recently updated my nRF Connect to the latest version 3.9.3 and it also updated the programmer app to 2.1.0. After this update, the Programmer app does not detect...
Upload fail - Remote DFU invalid CRC error
i m facing this error while uploading firmware through DFU kindly any one help me to fix this issue using nRF 52810
Thanks
Trying to update the Thingy91. While the nRF52840 updates ok, nRFConnect for Desktop reports " No matching trait found" when trying to update the modem on the nRF91.
The...
