Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi,
i need to stop one of my Timer at the falling edge of a Pin. So i need a gpiote_interrupt, is this right? Can someone help me how i can do this? if i write something...
I have 3 inputs I need to sample every n minutes. I have an n-minute timer that can kick off the first one, but I need to run the second and third samplings in succession...
We are creating our own dev board.
What pcb parameters were used for the PCA10004-nRFgo PCB antenna radio module 2.0?
1.6mm?
1oz Cu?
impedance control?
I have not...
Hello,
We want to use the J-Link Needle Adapter for nRF51822
The attached (capture.jpg) is the pinout from the J-Link Needle Adapter datasheet.
the attached (capture2...
Hi,
I have a wired problem with the nrf51422,
I'm loading the code using the J-link into my board or the evaluation board (PCA10007) that I have, the code runs perfect...
Hi all, I met a problem with measuring lithium battery voltage. I used 1Mohm and 250Kohm divided voltage, and used the internal VBG voltage as reference, and used ADC0 as...
I'm using a nRF51844
I'm writing my own ADC reading routines because I can't find any examples, but I know how to code so that's not a problem. I just want to confirm something...
Hi,
does a code example or app-note exists that describes how to configure the SPI peripheral to use an ISR to transmit data to a SPI slave?
Thank you in advance!
Dear
Do you know of a "present" /not present" low cost 2.4 GHz RFID chip for static asset monitoring in WiFi environment. compatible with, and actively associates with 802...
I am trying to hook up nRF8001 to TI MSP430F663x via nRF2740 module.
All inputs seems to be controlled properly.
Once I release the nRF8001 RESET line, RDYN goes low...
Hi,
I have a simple battery powered remote control device with a NRF51822 and using the Gazelle protocol for communication with the host.
To save battery the MCU goes...
The last few weeks I'm working with the nRF51422 and run in to several TWI/I2C issues. All of them I could solve except an issue with a SAA1064 7segment display driver from...
We have a custom board with nFR51422. Of the first 4 prototypes only one works correctly. This indicates that the PCB is ok. One difference is the chip marking. The working...
My test: PCA10000+Master Control Panel(3.4.0.8098) as central role, conninterval=20ms
nRF51822+softdevice(5.0) as peripheral role, conninterval=10ms
then sd_ble_gap_conn_param_update...