As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
The following settings are required to make I2S compatible with the AK5720VT.
MCLK=12.288MHz BICK=1.536MHz LRCK=32kHz Bit length=24bit
CONFIG.RATIO >= 2 * CONFIG.SWIDTH...
Hi All,
I have recently design my version 2 of my custom board, everything seems to work on the board, the firmware is fully running but i can't see the BLE device on...
Hi,
I tried to send audio with a sampling frequency of 44100hz, up until this point I had been sending the default sampling frequency of 48000hz.
For this I change the...
Hello,
I am trying to make radio test functions work on my 52840-based board using SDK 2.5.2. After some effort I managed to create a simple test program that partially...
I want to use P0.00 and P0.01 as UART pins. I have shorted the SB3 and SB4, and opened the SB1 and SB2 for using the pin as GPIO.
If I am enabling the " CONFIG_BOOTLOADER_MCUBOOT...
Dear Sirs!
I need that low power comparator on input AN7 reset controller when device is in OFF mode when voltage on pin drop below threshold.
Controller powered +1.8V...
Hi
I have a project base on Nordic sample code "v2.5.0/nrf/samples/cellular/Location" and it fully work with SIM card
now I need to use Onomondo softsim to replace SIM...
Hello, I'm getting these series of events often when the client is sending data to client. This is the the nRF SDK 17.
If I add a delay on the client app that is talking...
Regarding the description key Page 10 of the document "nRF Sniffer for 802.15.4" states "00112233445566778899aabbccddeeff", but does it differ for each device? Also, if there...
Hi there
During updating nRF5340 over bluetooth, really rarely the CPUNet fails to be updated over bluetooth.
The mcuboot says: Image in the secondary slot is not valid...
Hi Team,
I have 1 nRF5340 Audio DK. With the steps mentioned in below links, I configured Json file to Headset and I'm able to achieve it.
Setup Details : Headset - nRF5340...
Hello,
I'm using nrf52840 together with HX711 24bit ADC . My application samples the ADC every 12.5ms (80Hz rate) and the sample is sent out via BLE notification. The HX711...
Hi ,
I am using nRF52810 to start a project that combines BLE app UART and a timer. I found an example BLE app UART project from the directory nRF5_SDK_17.0.2_d674dde\examples...
