As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
We'd like to evaluate the nRF9160 for our device as a replacement microcontroller + LTE-M modem.
Working with the DK should be fine for evaluation purposes, but in the end...
I do the install by step , https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/gs_installing.html
the toolchain install failed when on step 5;
log as belowed...
Hi All,
I am currently implementing Write communication, referring to ble_app_blinky in example.
When the phone gives the command, the program will run this function,...
I'm attempting to control a PA attached to an nRF52840 in a way similar to Case ID: 212504
But I'm also using Zephyr...
Are there equivalent calls available via the Zephyr...
Hello，
We are using NCS v1.9.0 and nRF51820 SoC in our project.
Here is a question about using the COMP function.After I configure and initialize COMP，it returns NRFX_SUCCESS...
this is ADC config
This is the electronic schematic
Q13open，CURR N1和CURR P1 get parameter from temperature sensor 。OUT1 is temperature sensor ，it was 0.5Ω...
Hi,
i am working on nrf52 dongle. i want to use ble_app_uart example with it. how i can receive data on uart with usb. i can send data on ble but not receiving on uart....
I want to creat a hci vendor-specific command of zephyr using nRF connect SDK, based on hci_pwr_ctrl bluetooth sample.
At first, I think just using follow steps in hci_vs...
Hi,
Recently I have heard that there are license restrictions on using DKs for production programming. Is this only for production programming? Can I still use the DK to...
Hello, im trying to implement the UARTE Driver for simultaneous Use of Bluetooth and asynchrounos Uart TX/RX on a nRF52840 and nrf9160. The Problem is that neither RX or TX...
Hi
i want use a nRF52840Dongle as a Zigbee end device, when power up, i get following message:
I: nRF5 802154 radio initialized ***** delaying boot 5000ms (per build configuration...
Hi, I have just started evaluating nRF52840 using the dongle and Development Kit. I have successfully tested the Openthread network using CLI project. Now I want to try out...
Hi experts, The situation is following, the NRF53 shall receive multiple packets. After the reception of one of the packets the next one shall be received at the same frequency...
