I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Can the NRF54L accept a CMOS output clock signal on XL1? The NRF52s could do this via clock source register settings but such a configuration is not listed in the NRF54 datasheet...
Hello,
I was wondering if there was a way to implement a physical on/off switch to the npm1300 that would allow the outputs to be isolated form the battery but still having...
Hello,
I'm looking to get XInput working on the nRF52840 so that our device can appear as an Xbox-compatible game controller. I'd appreciate any guidance or recommendations...
We are checking the feasibility on LE Audio + Mesh + Bidirectional streams. A picture is attached for the situation. We would like to know how to apply Mesh network on LE...
We're designing a board using the Thingy:91X as a reference design. We're trying to determine if all of the power components are required.
The nPM1300 appears to provide...
Hello,
We have a requirement to ensure all private keys are stored within AWS Key Management System (KMS) and the only way to interact with these is via the KMS APIs that...
Hello,
The documentation in the nRF7002 Product Specification rev 1.0 says that the P2P mode (Peer-to-peer) is supported (section 6). However in this ticket: https://devzone...
I recently had a question about AES encryption on the nRF9160 and about how to store 32-byte encryption keys. The ticket was closed after I got the following answer: " we...
Hi,my board is nRF52840,and the demo is periodic_sync_conn within ncs2.7.0,
I want to establish periodic sync with the AP whose rssi is better，but i am failed。The ESL will...
Hello Nordic team,
I am working with the samples/bluetooth/shorter_conn_intervals sample on NCS v3.2.3 using two nRF54L15 DK boards.
I understand the difference between...
Hello, Recently I got an nRF9151-DK and I am following the Cellular IoT Fundamentals course. When it was time to connect the device to nRF Cloud (Lesson 1, Exercise 1), it...
Hi there,
I am developing a Matter light color temperature lamp product based on the NCS v3.1.1, and I need to store some custom user data in NVM (Non-Volatile Memory) within...
Hi engineers,
I posted a question at the link below, but it doesn’t seem to have received a response yet. If it’s convenient, could you please help answer the question?...
I'm debugging the function of switching between ESB and BLE. My general approach is as follows:
Initially, the BLE protocol stack is initialized, advertising starts...
