Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hello,
i am using the Wi-Fi: Scan sample with the nRF 7002 Deveolpment Kit.
I am trying to alter the clock frequency/QPSI mode (Dual/Quad) of the QSPI Bus connecting the...
Hi, We currently have a custom board with a nRF54L15 (final production silicon) paired up with a nRF21540 RF front-end module (FEM). This board is running Zephyr with v2.9...
Hi. I am using nrf52832 and 17.0.2 sdk.
What I want to do is to provide automatic connection between my nrf device and my android device. For this purpose, I use the HID...
I'm trying to use AAR peripheral, but I don't know the structure of output DMA job list, as it's not defined in the datasheet. I was trying to use one job pointing to flat...
Hi,
I'm transmitting using the nRF24L01P and using the nRF52810 as the receiver, 5 byte address.
We send a 2 byte packet usually 0x00, 0x00 until data is ready. If I set...
BT_DRV_RX_STACK_SIZE is too small and can't be configured. It needs to be more than 512 bytes in released versions of Zephyr, or 640 bytes, on the main branch. Note: I'm using...
Good morning everyone,
I am going crazy to solve this problem, but I hope we can figure it out with some help.
I am working on a prototype for which we need to use a...
The documentation for the Maximum Performance sample mysteriously states that the sample is not supported on the 5340 with no explanation as to why. As I am getting spurious...
Dear support,
I am using this board: https://www.nologo.tech/en/product/otherboard/NRF52840.html#%E5%BC%95%E8%84%9A%E5%9B%BE . I am trying to use any analog input to eventually...
nRF Connect for VS Code v2024.12.55 showed up yesterday and it seems to be broken for me; the "build", "flash", debug" buttons are not available to me, I am stuck with "Pristine...
Hello,
I fear that my toolchain and environment is seriously confused.
When i use the vs code extension sdk to install a toolchain or sdk i get the following message ...
I Have been trying to interface mpu6050 with nrf5340 DK .
f ( NOT "${ret}" STREQUAL "0" )
message (FATAL_ERROR "command failed with return code: ${ret}" )
endif (...
Hi,
I'd like to know what is the cause of the stall in
sym_E5Q6O4GY4KO3GMW7WJYXLZKHO7ZGDWLU4ZPAKWA() at 0xa55a
when calling sdc_hci_cmd_le_set_adv_enable ?
Here is...
I am currently considering the use of an external Flash IC for a Matter device.
I have two questions and would appreciate your help:
1. Is the MX25R6435FZNIL0, which is...
Hello,
according the datasheet the nRF52832 has an gain error of 0.02%/ ◦C and E_G1 of -3 ... +4%. This is too high for our requirements. Is there a way to improve this...
