Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hello,
How can I have two or more temperature probes reporting using the ZCL library?
Imagine that I want to have a device that measures for instance two temperatures...
Hi,
I am trying to measure the current of a custom board using PPK board, My custom board takes 5 Volt input supply but PPK board has a 1.8-3.6 Volt external power supply...
I am trying to modify the nRF52840dk_nrf52840 spi_flash sample, ncs/zephyr/samples/drivers/spi_flash , to use dual QSPI.
Following is my device tree configuration:
I...
I am able to pair a peripheral device using advertising 16bit UUID to the Central Device(nRF52840-DK board).
Also I am able to read the Battery level service and Device...
Hi, I have successfully achieved the OTA DFU function on nRF52805. This is what I can see now:
Step 1) I can see the Nordic_Buttonless BLE signal. After connection, there...
When using the nordic power profiler for the nrf52840, it gives the "idle" current as 2.7uA. Presumably this is the deep sleep current, but it seems like this number doesnt...
I've been using nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8 for my development. I'm trying to switch to the nRF connect SDK. I'm having a hard time figuring out where to...
Hi everyone,
So Im trying to modify the event handler of the ATT_MTU example file to have it so that it logs every time a byte is sent / instead of KB but for some reason...
Config options for enabling SDHC card support are not working with nrf SDK V1.6.0. Unable to create the project using Segger IDE.
The same options are used with nrf SDK...
Hello,
We are switching our firmware from the old sdk into the NRFConnect zephyr sdk and I cant see any way to retrieve the channel of the advert when scanning. We need...
Hi everybody,
i've got an issue i want to discuss here. I'm building a webserver using the nRF9160DK with ethernet-shield from PHYTEC and an SD-card which holds the frontend...
Hello,
So I was exploring the nRF52840 DK as a Zigbee device when I found this page: Zigbee CLI wrapper .
This seems very promising, having a python CLI to interface with...
Hello,
I'm doing a project with Zigbee using the nRF52840 and I want to read some sensors that talk via UART.
I have ported with success the nrf_uart example but after...
dear all
Can keil compiled library be used in segger embedded studio? For example, I have a paw8001_ ofn114009_ 12_ m4f_ keil.lib
Library, can I put it directly into NRF...
