Hi,
We designed the circuit followed the reference circuit(QFN48), but we always failed in the 8kv ESD test.The CPU always reset while ESD testing.
The 8kv ESD power...
Does anybody got an app inventor2 "project" to communicate with the (Adafruit) Bluefruit LE UART (or SPI) ?
Note: my Android version is 4.4.2 (LE "advertising" not supported...
I've created a Secure DFU client using the multilink central example with S130 and SDK 12.2 (running on PCA10031).
There are a few issues we have trouble with.
The...
Hi,
After successfully managing to preserve our devices bonding information (and custom app context data) across DFU updates, we have a few related questions.
I should...
I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Is there any pre-existing library similar to the Arduino avdweb_VirtualDelay library available for the Nordic Semiconductor nRF52840 Dongle? I do see the procedure on how...
Hello In SDK 2.6.xx I used to define an extra CMake argument in the VSCode UI, i.e "-DMFG=1" This argument was available when CMakeLists.txt was processed so I could do additional...
We have difficulties to get RTT prints from MCUBoot while performing DFU.
As far as I understand Segger RTT is reinitialized when booting Application and this might be the...
I want to change the bitrate for different settings：
Different settings with 48khz&10ms:
I try ot change the prj.conf to add these:
But an error occurred during...
Hello,
I have a device that I want to operate on the lower range of RSSI (but still around -80dBm and have problems with disconnect. I would like to understand if there...
I want to capture device log. How to capture device log ? Which configuration I need to enable in SDK ? Can you provide sample example which capture device output log ?
We are planning to use NRF52840 for a medical device would like to know from Nordic or anyone from the forum about the verification/validation of SOUP (Software of unknown...
Hi, I am encountering multiple conflicts in the device tree view, which seems quite strange.
"Oscillators" appears to collide with regulator@4000 .
"Clock" appears to...
Hello,
We are in certification stages for our custom product based on the nRF7002DK. Our application requires BLE and WiFi to be operational simultaneously. Consequently...
Hello,
I am new to developing with Nordic products. I have experience working with other microcontrollers like Microchip and STM32. Both of those have their own IDEs. Does...
I would like to integrate System OFF mode of operation into idle system hooks in Zephyr (i.e. when the CPU is idle, it goes into OFF power state automatically). As it currently...
Hi there,
I want to advertise to multiple specific BLE addresses, but I don't know how to implement it with the nRF Connect SDK. Please suggest.
I aim to advertise to...
I am using an nRF52840 and nrf52832 to measure distance, but the reported value is almost twice the actual distance . For example, when the actual distance is 1 meter , the...
Hi,
the nrf45L15 datasheet v0.8 says on page 277 "Note: TWIM and TWIS must use clock pins for both SDA and SCL.".
However in the table 72 on page 795, only the SCL pin...
What is the industry best practice for controlling the on/off state of an nrf52 using a momentary push button? Do designers use nrf’s deep sleep mode or properly cut off power...
