Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
Hello, I get the
"ERROR: The --family option given with the command (or the default from nrfjprog. ini)
ERROR: does not match the device connected."
message after...
Good morning,
this is Algocraft (www.algocraft.com), an high tech company whose core business is to develop, design and market a wide range of professional systems dedicated...
Dear Nordic Support Team,
I am working with the nRF52840 and need to configure the SPI peripheral in Zephyr to operate without DMA.
I’ve encountered a few problems:
...
I am able to update the app core successfully from an external flash partition via the `mcumgr` desktop tool. However, this is not working for the net core.
It successfully...
I would like to create a thread based sensor and use Apple/Amazon/Google smarthome hubs as the OTBR. How do I commission a thread device (not a matter device) to these hubs...
Hello,
I'm working with Zephyr and using MCUBOOT as bootloader.
Due to HW design I have to set and hold a gpio as fast as possible when the application boots (to prevent...
Hello,
We're seeing an error that only happens after a cold reboot (unplugging the battery and replugging it) and it happens inside the bootloader while trying to open the...
Dear all:
I used this command to build light switch for 5340DK:
west build -p always --build-dir nrf/samples/matter/light_switch/build -b nrf5340dk_nrf5340_cpuapp nrf...
Kconfig failed: [Errno 22] Invalid argument: 'c:/users/user/zephyr/kconfig"' is an error that appeared this morning. What is supposed to be in the Kconfig file. I have been...
I can't remember where I found it now, there was a file somewhere that listed all the files in a project. It had
absolute paths which filled me with dread as it means a...
Hi
I am working on a custom board and have hit an issue with the software part. When the nrf_modem_lib_init function is invoked, it always ends with a timeout (errno ...
Got a Thingy91 (not the x model) that doesn't show up as anything when connected to a PC by USB, except when in bootloader mode, by pressing SW4 (no reaction with SW3) when...
I read other similar issues on this forum but they haven't helped solve my problem. I started with the peripheral_uart example project. Development and execution on the target...
Sorry for long sentence. The nRF5340 document describes about the Reset. This chip set have the POR. so, if POR function work, I don't need to use the PIN reset. because POR...
I have configured my application according to the Throughput example. The prj.conf file inside the sysbuild\ipc_radio folder is not being considered in the build. As a result...
Hello, everyone.
I would like to use mcumgr to update the firmware of a nrf52 via another nrf52 over uart.
From the documentation I understand that smp supports uart so...
Hello,
I just got started with the nRF5340 DK. I went through the example which instructs how to load the "Blinky" applications, build it, and then flash it to the Board...
