Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am using NUS to work with...
Hey,
I'm currently working on a legacy project that uses the NRF5 SDK. Rewriting the project to use the nRF Connect SDK would be tedious, time consuming and likely to introduce...
We're having an issue where our nrf52840 appears to stop advertising, and isn't able to resume advertising.
Our device is a custom PCB based on the Thingy91 (has both an...
We have a product based on the nRF52840 which uses the GC9A01 display driven using SPI on battery power. The device also functions as a Bluetooth connectable so it is normally...
Hi,
I'm trying to implement an application that acquires data from two channels of the SAADC in "parallel". I'm currently using the nRF52 DK and nRF5 SDK v17.1.0. After...
Hello,
I'm using nrf52840 together with HX711 24bit ADC . My application samples the ADC every 12.5ms (80Hz rate) and the sample is sent out via BLE notification. The HX711...
Hello, I am currently using (\nRF5_SDK_17.1.0_ddde560\examples\peripheral\radio\receiver)routine to develop.I want to check if the first N bytes of the received packet are...
I am looking to program the nRF52840 development board to get data from the mpu6050 sensor. I want to use bare metal code for the same. Is there any available code or sources...
I am trying to program nrf52840 to print acceleration from mpu6050. But when I build the project, I get the error - undefined reference to `nrf_drv_twi_init'. Here is the...
I tried to use mcumgr to write and read files to the littlefs of 9160. According to the instructions, I will enter mcumgr conn add acm0 type="serial" connstring="dev=/dev...
Hi Folks!
I've got a rather bulky project that's having a rather bulky project. In short, my project tries to enable both MCUBoot DFU and an ExFat Filesystem. I've narrowed...
Support,
I've encountered a challenge while integrating my product with device from a third-party. Unfortunately, they've utilized the SIG base UUID for their unregistered...
We have an existing application for the NRF52840 using SDKv15. This application will handle writing a new application to a free bank. I need to add the ability to jump from...
HI currently i am utilizing sdk ver 17.1.10 nrf52840 s140 we are using dfu/secure_bootloader/pca10056_ble app and i need to add UART app to it so that so we need both bootloader...
I need to do a DFU via BLE but I do not have enough memory. For the past few months I have been working on a custom bootloader that would use an external memory to do the...
Hello, I am on conenct SDK 2.6.0 and trying to run the Zephyr Bluetooth:Central example on the nrf5340 dk to connect to a Minew S4 door sensor and get data from it. Here is...
I am working on firmware that acts as a BLE sensor hub to pipe BLE data from connected sensors to a PC over USB (using the CDC ACM UART interface). The peripheral sensors...
Hi,
I am developing a nrf5340 based device (no external memory) using FOTA to update the firmware. This process used to work quite well for a while now, but I ran into trouble...
I am working with nRF Connect SDK 2.6.1 on a Central and a Peripheral and I am running the BAP similar to the nRF Audio Example. I am using out of band pairing over UART for...
Hi, I am working on using nrf7002dk to connect to AWS over WiFi. So far I have been able to connect to WiFi and send a HTTP get request through DHCPV4. When I continue to...