Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
What are the limitations on drawing current from the nRF52840 VDD pins? Are there continuous and transient limits on how much current can be drawn?
We are powering peripherals...
Hello,
I am working on adding BLE central capabilities to our device by using the ble_app_multilink_central example project as a template. Currently I am adding the expected...
Hi,
I development a elock device to use nordic 52832 chip. I want to transfer some information between phone app and my device. Like UUID / user account / user password...
Hi, My PC have already installed the nrf connect sdk with version v1.2.0. How can i update the nrf connect version to v1.2.99-dev1? Please give me a few complete steps .
Hello everybody, i am trying to use BLE central uart sample software in zephyr, on nrf52840 dongle. I mapped the uart outputs on pins 20 and 24 of the connector, made the...
I have created custom characteristics by
BT_GATT_SERVICE_DEFINE ( vnd_svc ,
BT_GATT_PRIMARY_SERVICE (& vnd_uuid ),
BT_GATT_CHARACTERISTIC (& vnd_enc_uuid . uuid ,...
I am using the current nrf-sdk v2.1.0, which includes the matter version v2.1.0 from the Nordic repository.
I encountered an error that setting CONFIG_DEBUG will result...
Hi
I have successfully used the TIMER & GPIOTE to generate dual tone frequencies for a BFSK project. 200kHz & 400kHz. ( 50% duty cycle square wave)
I wonder if the same...
Hi,nordic
I am using 52832. The SDK is mesh500 and sdk1710. I want to check the data sent from the PC through the serial port. Where am I and how do I read the data?
I am using the NRF52 development kit and I modified the uart example main.c to simple TX and RX application using printf function. The board is directly connected to the PC...
Good morning,
I ended up changing the design to use the nRF52810 chipset and I wanted to find out if Nordic would be able to provide some schematic feedback for my design...
Hi Nordic expert,
We are K5DET1/3/5/7/9/11 output high level, then string 10K resistor, K5DET2/4/6/8/10/12 through the mercury switch to read this high level, while adding...
Hi,
According to the documents of NCS, CoAP Server sample uses native OT CoAP API while CoAP Client sample uses Zephyr CoAP API, and the Zephyr CoAP API is recommanded....
I've googled all over, and I'm having a hard time finding any documentation that digs into how to use the nRF Connect SDK. Most documents point to examples, however the wealth...
