This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
Hello i realize the nRF24L01P is NRND. Curious if you are able to answer w/out too much work as to whether one of the other nRF devices allows access to the radio to use the...
Hi:
I set up a fresh install of the NRF Connect Extension Pack in VS Code on my MacBook Air M4 and was able to build and flash the Blinky demo to my nRF52840DK. The issue...
Hello, this ticket addresses three issues:
1. After installing nrfutil with subcommands device and toolchain-manager and sdk-manager, into %USERPROFILE%\.nrfutil, everything...
Hello,
Since our Product Launch we have gotten feedback that pairing with some (but not all) Apple devices is a significant problem. Even through several attempted fixes...
After upgrading nRF Connect SDK from 3.1.1 to 3.2.1, our fixed regulator stopped working. We are on nRF54L15. Tracking it down further, this seems to be some sort of GPIO...
Hi,
I am porting a product from SDK 15 to SDK 17 and to Nrf Connect.
We need to maintain code combability as far as possible between products using SDK 15/17 and products...
I'm creating a system test for manufactured units and if it's OK I would like to set a permanent flag in an area that will not be erased if I erase flash at a firmware update...
nrf sdk 17.1 example:peripheral/uart/pca10040 I attempted to use P0.9 and P0.10 on the development board to set up a UART serial port for data transmission and reception ...
Hi,
I am on NCS 2.9.0, I have tested lesson 5 exercice from NRF Intermediate course about BLE DFU, I have some questions about it:
- with mcumger, is there a way to update...
Hello,
We have a custom board we are developing on that uses the nRF54L15 MCU. The board has some LEDs that we were hoping to drive using PWM, but these are connected to...
Hi all
I have some trouble with a new batch of nRF9151 chips.
The old one had the Firmware: 2.0.2
The new ons have the Fimrware 2.3.5.
My application does no longer...
Hello
I tried to test OTA function with smp_svr example.
I want to use the external flash mx25r64 on nrf54l15-dk(v0.9.3) to store update Firmware over BLE. SDK version...
Hello,
I have some unclarities for the APPROTECT mechanism on NRF9151.
Basically, I had a misunderstanding of the involved CONFIG features, and as a result I used CONFIG_NRF_APPROTECT_LOCK...
Hello,
I’m using an external NFC reader/controller (NXP PN7160A1HN/C100E) connected via I2C to an nRF52840 module (Raytac MDBT50Q-1MV2) on a custom PCB. (Programming is...
On nRF52840, after power up, I continue to randomly get hangs. I am having trouble figuring it out, but it seems every time I encounter the issue, it is related to RNG. If...
