Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
SDK: NCS 1.8.0
Based on: Peripheral LBS example
Central: Mobile (iPhone)
Peripheral: nRF52832
Hi,
I am attempting to integrate NVS within my custom application based...
Hello,
I noticed that nrf_ble_lesc_request_handler() hangs when I have NRF_CRYPTO_BACKEND_CC310_ENABLED and use a NRF_SDH_BLE_TOTAL_LINK_COUNT bigger than 5. Using the Oberon...
Hi,
I have the following error when trying to compile either the light_switch or light_bulb matter projects on nRF Connect SDK v1.8.0:
opening dependency file C:/Users...
Hi i have a problem i put buttonless dfu on my chip and everything went ok i can do OTA updates and everything works perfecly but i have a problem when i connect via j-link...
Hi,
Is there a low power consumption for battery powered long term (months) application for Nordic Thingy 91? I don´t need GPS position, just to receive sensor data and...
Hello
Using a Thingi91 with latest firmware and Asset Tracker v2. Connects to the tower, but cant seem to connect to the NRF Cloud. How can I check if it can reach any other...
Hello all
I am using the Thingi:91 in Sri Lanka. I can connect to the tower correctly, but cant get data connectivity yet. I am told by the operator that they use the following...
On nRF cloud I registered the ibasis sim card which came with the 9160DK and connected it to that 9160DK device. I'm now using a Fanstel BLG840F and wanted to know if the...
hello Nordic
i am using nrf52840, with zephyr
i wish to use the nrfConnect Tx power service to read and to SET my Tx power
but in ncs in zephyr/subsys/bluetooth/services...
Hi,
I am using nordic52840 dk board.
And i want to flash a bin file using nrfjprog command line.
For Hex file i am using below command
nrfjprog --reset --program blinky_pca10056...
Hi everyone,
We are using the nRF5340 and need to use an LFXO, not just for BLE, but also for the real-time clock that our product should provide.
Due to other requirements...
Dear Team,
Just I have purchased Thingy91. Please help with where I can see the demo to start with some basic example of transferring data. Mentioned that Pre-loaded assert...
I just installed the nRF toolchain and Programmer application to start using my nRF52840-DK eval board. I have the board connected through J2 to my computer and I can flash...
hello Nordic
i am using nrf52840 with zephyr ncs
unfortunatly i used this command "pamac install downgrade" at one point
since then i can not use 'west flash --erase...
