Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
Hello,
I'm using the following setup:
nRF Connect SDK v2.9.0
B0 , upgradable secure MCUBoot, and application
Statically defined partitions in the partition manager...
I am experiencing issues configuring an SPI-based SD card interface on my nRF5340DK using NCS v2.7.0. The SD card is not initializing correctly, and I am receiving repeated...
I have two nRF52833 development boards: one is connected to the nRF21540 EK as TX (using BLE peripheral_uart), and the other is used as RX (BLE central_uart). My issue is...
Hello,
I recently updated to the "new" nrfutil tool and installed the nRF Sniffer according to the instructions. I programed the firmware and ran nrfutil ble-sniffer bootstrap...
Hi.
I am looking for help with software development for my Thingy91 project.
Project is very basic and I am ready to pay based on hour rate. It is very simple and beginner...
Hi support team,
I'm working with nRF52833 DK. installed the mobile app and desktop, but I wasn't able to connect to either.
Power switch ON, SW6 on DEFAULT. J2 connected...
Hi
The Blinky Programm only starts when I give the reset Go command via jlink commander.
At Power cycle nothing happens.
If i give the SOC an external Pin reset the...
We have written a Flutter app, which uses the Flutter-nRF-Connect-Device-Manager package to perform firmware upgrades on bluetooth devices that the app bonds with.
If iOS...
Hi,
I’m looking at starting a new design that would be based on the nrf52840, however it seems that the flash readout protection is now fairly broken on this device. Are...
Both myself and a colleague had an issue in the past 48 hours where upon launch we were prompted to install a new West workspace/SDK. In my case it "tricked" me into installing...
SDK: 2.6.1 (2.9 seems to give an HCI build error , undefined reference to `__device_dts_ord_135', when enabled CONFIG_BT_LL_SW_SPLIT, CONFIG_BT_LLL_VENDOR_NORDIC ?)
SOC...
Changelog for nRF Connect SDK v2.2.0 mentions that:
nrf_dm_high_precision_calc() now handles out-of-memory errors by returning NaN .
What exactly are the memory requirements...
We want to generate 8.200 MHz as I2S MCK with an nRF5340.
This could be achieved with 12.300 MHz ACLK as source for MCK, and then dividing by 1.5 in the Master clock generator...
Hello evebody,
I have problem with socket creation. I am trying to copy example of this tutorial:
https://academy.nordicsemi.com/courses/cellular-iot-fundamentals/lessons...
I am trying to get DFU FOTA over BLE to work using external flash on an nRF52840 DK with NCS 2.5.2 . I followed multiple sources, but I am unsure about the correct configuration...
