I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
I've been struggling with this for some time now and no matter how I approach it I can't quite get it to work. I'm essentially looking for something like the "maximum performance...
Hello, I have several development-related questions about the microphone functionality of the NRF5340 AUDIO DK in headset mode:
Is it possible to configure the device...
I saw in this video that there was a lipo battery being used with a nrf52 Development Kit and I read this in the spec for the nrf5340 Development kit:
1.7-5.0 V supply...
Hi,
I am connecting a central to multiple peripherals. In order to optimize the throughput I would like to simultanuously sniff the connection. In the nrf Sniffer documentation...
We are producing an issue where the ZBOSS stack will emit a ZBOSS Fatal Error without any context if we alter ZB_DEV_REJOIN_TIMEOUT_MS. Specifically, the steps to reproduce...
Hello! I am trying to get gazell to work on the nrf52840 dongle.
I built the nrf connect sdk Blinky project with the nrf52840 dongle set as the config. then pushed the merged...
In the past, we've been able to use the nRF52-DK to flash our boards, supplying power through the debug port by shorting SB32.
For our L15 prototypes, the nRF52-DK doesn...
Hello Team,
I am experiencing an issue with the sound output from an external codec connected to the nRF5340 DK. Currently, the sound is in mono, but my goal is to achieve...
Hello,
I recently purchased a few NRF9161-DK boards for both LTE and NR+ evaluation. However, I am unable to run through the initial demo. The board is discoverable initially...
NCS 2.7, nrf52840, sysbuild with mcuboot, multiple board revisions
I have setup my build to use different keys for each board revision with this in my sysbuild.conf:
...
Hello DevZone,
I just located a mysterious bug , it's about printk() and low power.
Environment:
NCS v2.8.0 and v2.9.0
nRF52840DK v3.0.2
PC: Ubuntu 22.04
Zephyr...
Hello. I am attempting to run the Matter Template app sample on the Adafruit Feather nRF52840 Express board.
I created a pm_static.yml file with the following configuration...
Hi,
I am using nrf52840 with nrfSDK-16.0, Ble5 coded PHY( S=8 ). I am using ESP32S3 as central and nrf52840 as peripheral device. I want to connect to 8 peripherals with...
When I try to program the Thingy:91 in cellular mode, it always gives the message 'Failed to connect to port.' I’ve tried different ports, but I get the same result.
