I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi all,
I'm working on a custom Bootloader for my nrf52840-based board, and it needs to support DFU from external SPI Flash. I previously was successful with a "first draft...
We want to start with ble_app_uart example for our product but it the firmware halts at CRITICAL_REGION_EXIT() in nrf_sdh_enable_request.
We are using the example from 17...
Hiii, is there any libraries or example to read nfc tag through clrc663 nfc reader, could any one direct me to the any solution
thanx in advance
suprith
I am having problems setting up UART communication between nrf9160 and nrf52840 on Thingy91. My set up consist of a Thingy52 and a Thingy91. I am using ncs version 2.0.1....
Hi,
I've been working on Open Thread recently. I found that after I send provisioning request, even though there are 3 servers "enabled provisioning", the callback function...
Hi,
I am trying to setup a raspberry pi 0-W for flashing nrf devices. But nrfjprog doesn't seems to work.
I am using Raspberry Pi OS (32-bit).
I have fetched Segger...
Hello everyone,
I've got a simple question here today. I'm making use of the nRFCloud on our nRF9160-based system.
When using the different APIs to nRFCloud, be it location...
Hello team,
I am having a problem running LWm2m sample out of the box on Thingy91 (SDK 2.1.0, programmer 3.0.4). If I enable any of the sensors using something like the...
hi Team,
i am using Microsoft Windows 10 Enterprise OS and segger 5.40.
i am using nrf52840 DK device in my project.
i downloaded nrf connect for desktop software and...
Hiii team,
I am using the nrf52840 DK I want to connect the slave to the master How to connect a slave with out using a dedicated spi or i2c by using the simple GPIO pins...
American Semi produced this Silicon on Polymer IC a little while ago
Interested if anyone knows of this being used in a small form factor module
Seems as if they must...
Hi, We are starting to work on a production tester which will need to program a DUT based on the nRF5340. Both cores will need to be programmed and an external QSPIFLASH memory...
I've put the recommended circuit for the nRF52810 QCAA chip together on breadboard (schematic is below) and am using a J-Link Edu Mini to program.
I created a custom board...
When using Segger Embedded Studio, multiple build targets can be defined. Each build definition can have its own "defines", libraries, etc.
When using Visual Studio Code...
