hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
There's a few threads out there with similar questions, but I haven't seen a direct answer to this.
If I build with nrf5340dk_nrf5340_cpuapp, can I use the entire application...
Hi,all~
The program runs on nRF52833. At the beginning, MCU sends data to nRF52833 through serial port, and the data can be received correctly(pic one）. When I use THE...
I currently have an issue where by the Chip-Select is not toggled at all when configuring the csn pin to pin <18> on the Nrf52840 using Zephyr (version 2.7.1).
See dts configuration...
Hi All!
I am using NCS v2.0.0 and nrf52820 custom board and an example to test is radio test . I tested that example with nrf52833DK , code is executing/ printing messages...
Hi!
I'm developping a battery powered product, so the power consumption is important. I need to multiple an array point by point with an array (hamming window) that I store...
Hello support,
Your choice of 201 size component packages are not ideal for manufacturing (and HW debug). I understand some of the reasoning especially on 21540 antenna...
Hi,
I'm trying to implement zigbee into our application. For testing purposes I start with the example code, and I use the multiprotocol template as a starting point.
...
Hi
I am trying to migrate my project to newest NCS v2.0.0 but is struggling figuring out how to configure SPI2 slave operation mode.
The project is currently running v1...
Dear Nordic Team,
your chip above is on 52 weeks lead time, so here is the question:
a) I can spot inventory for the 8 channel version: nRF24AP2-8CHQ32 - would this...
Hi,
We are trying to add lwm2m (client) into light bulb sample (matter).
It results a redefinition of gethosname : CONFIG_LWM2M defines CONFIG_NET_SOCKETS_POSIX_NAMES...
Hi,
I have a nRF5340 DK (not the audio DK). I read the specification of nRF5340 Audio DK and found that it supports LC3 codec. However, I want to ask, is it possible to...
Hi,
I'm trying to measure the current consumption of the nRF9160 DK using a Nordic PPK 2 in various modes. Through reading up various documentation regarding this, I have...
I've installed nRF Connect and VSCode on a MacBook Air M1. Whenever I try to build my existing firmware that builds fine under Windows, I get the following error:
The terminal...
Hello together,
I have my own MAC addresses and want to make Zephyr use them. How can I do that?
What I found out is that the firmware read the MAC from settings "bt/id...
From everything I've read, I should be able to see log output in the "LTE Link Monitor" when logging is enabled. Instead, it appears to freeze up the LTE Link Monitor and...
